Black+Decker WP1500K Manual De Instrucciones página 15

Selecting the correct operating speed
The work speed of the rotating part is controlled by the
timing. Switch indicated in figures. The further the switch is
moved away from its off position, such as from 1 to 2, the
faster the work part rotates.
Operation
Make sure the polisher is in the "OFF" position before
plugging the polisher into an appropriate power outlet.
To switch your polisher on, press the on/off switch. To
switch it off press the on/off switch.
ALWAYS START AND STOP THE POLISHER ON OR
AGAINST THE SURFACE. Place the cord over your
shoulder and do flat surfaces first - hood, trunk and
roof. Cover areas quickly with broad, sweeping strokes
in a criss-cross pattern. DO NOT press down on the
polisher. The machine's action, not pressure, does the
best job.
After flat surfaces are covered with wax, do sides of
the car. Let the cord hang free. It is not necessary to
use a criss-cross motion on doors and fenders.
Put a clean polishing bonnet on the polisher
Polish the wax. Use long, sweeping strokes in a criss-
cross pattern. Do not press hard. Let the polisher do
the work.
Warning! Before working , let it operate for no less one
minute without load. First , ensure that the polisher disc is
resting on the work surface. Grasp polisher and turn it on.
Move it in long, sweeping strokes along the surface, letting
it do the work.
HANDY HINTS
This polisher is a random orbit polisher. it is designed
to wobble. The wobbling motion produces the fine,
swirl free finish.
For best results, use light pressure only, letting the
polisher do the work.
Exercise caution around edges, corners or small
surface areas. Prolonged polishing on edges and
corners can damage these areas.
Polishing bonnet can be hand washed in warm water
and mild detergent. It can be machine dried at the
lowest setting however air drying is recommended.
DO NOT USE ABRASIVE COMPOUNDS. Liquid wax
is recommended to use with this polisher.
The polishing bonnet is only to be used for the final
buff. Do not use it to apply wax.
MAINTENANCE
Keep guards, air vents and the motor housing as clear as
possible of dust and dirt. Wipe with a clean cloth and blow
through with a low-pressure air supply. Excessive build-up
of metal dust can cause tracking of electrical current from
the internal parts to exposed metal parts.
ENGLISH • 15
Warning! Before performing any maintenance, switch
off and unplug the tool.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service personnel,
always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
serv- ice center.
Warning!The use of any accessory not recommended
for use with this tool could be hazardous.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your
BLACK+DECKER product needs replacement, or
if it is of no further use to you, do not dispose of it
with household waste. Make this product available
for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
SERVICE INFORMATION
BLACK+DECKER offers a full network of company-owned
and authorized service locations. All BLACK+DECKER
Service Centers are staffed with trained personnel to
provide customers with efficient and reliable power tool
service. For more information about our authorized
service centers and if you need technical advice, repair,
or genuine factory replacement parts, contact the
BLACK+DECKER location nearest you, or visit us at www.
BlackandDecker-la.com
SPECIFICATIONS WP1500K
Voltage
AR, B2, B2C 220V
B3 120V
BR 127V
Power 1300W
No-load speed 1000 - 3000/min (rpm)
Disc diameter 7" (180mm)
Spindle size 5/8"-11/M14
Cord 1.8m