Before Putting The Equipment Into Operation - Dexter 900ID2.5 Instrucciones Legales Y De Seguridad

FR

5. BEFORE PUTTING THE EQUIPMENT INTO OPERATION

ES
PT
To install the bit
To install the bit
IT
When selecting a drill bit, use the right type for your job. For best performance, always use sharp drill bit.
When selecting a drill bit, use the right type for your job. For best performance, always use sharp drill bit.
EL
1. To open the chuck jaws, hold its collar while turning the sleeve in the counterclockwise direction. Insert the drill bit deeply into the chuck, and
1. To open the chuck jaws, hold its collar while turning the sleeve in the counterclockwise direction. Insert the drill bit deeply into the chuck, and
then center the bit in the chuck jaws.
then center the bit in the chuck jaws.
2. To close the chuck jaws, hold the collar while turning the sleeve in the clockwise direction. Tighten securely.
2. To close the chuck jaws, hold the collar while turning the sleeve in the clockwise direction. Tighten securely.
PL
3. Remove the drill bit in reverse order.
3. Remove the drill bit in reverse order.
UA
RO
Forward /reverse adjustment
Forward /reverse adjustment
EN
1. For forward (clockwise) rotation, push the forward /reverse switch to the left position.
1. For forward (clockwise) rotation, push the forward /reverse switch to the left position.
2. For reverse (counterclockwise) rotation, push the forward/reverse switch to the right position. Although an interlock prevents reversing the tool
2. For reverse (counterclockwise) rotation, push the forward/reverse switch to the right position. Although an interlock prevents reversing the tool
while the motor is running, allow it to come to a full stop before reversing.
while the motor is running, allow it to come to a full stop before reversing.
Auxiliary Handle
Auxiliary Handle
An auxiliary handle is packed with the drill for ease of operation and to help prevent loss of control. The handle can be rotated 360°and it can also be
An auxiliary handle is packed with the drill for ease of operation and to help prevent loss of control. The handle can be rotated 360°and it can also be
mounted on the opposite side for left hand use.
mounted on the opposite side for left hand use.
Loosen the handle by turning the handle counterclockwise.
Loosen the handle by turning the handle counterclockwise.
Rotate the handle to the desired operating position.
Rotate the handle to the desired operating position.
Securely tighten by turning the handle clockwise.
Securely tighten by turning the handle clockwise.
Depth gauge
Depth gauge
Change the position of the depth gauge, turn the grip of the handle anti-clockwise until the depth gauge is loose enough to slide in the hole. Set
Change the position of the depth gauge, turn the grip of the handle anti-clockwise until the depth gauge is loose enough to slide in the hole. Set
the depth, checking the depth with a steel ruler for most accurate measurement and then turn the handle grip clockwise to tighten both the depth
the depth, checking the depth with a steel ruler for most accurate measurement and then turn the handle grip clockwise to tighten both the depth
gauge and the auxiliary handle in the required position.
gauge and the auxiliary handle in the required position.
Selecting the impact/drill mode
Selecting the impact/drill mode
The impact/drill switch should be set according to the type of action required. The tool has two settings:
The impact/drill switch should be set according to the type of action required. The tool has two settings:
Drill mode : For drilling into wood and metal. Use standard drill bits. Drill mode : For drilling into wood and metal. Use standard drill bits.
Impact mode
Impact mode
5. BEFORE PUTTING THE EQUIPMENT INTO OPERATION
WARNING: The device should be disconnected from the mains before putting
WARNING: The device should be disconnected from the mains before putting
into operation.
into operation.
NOTE: The chucks of reversible drills are always fixed by a screw with a left hand thread.
NOTE: The chucks of reversible drills are always fixed by a screw with a left hand thread.
The screw must be loosed before the chuck can be removed if necessary. To loosen the
The screw must be loosed before the chuck can be removed if necessary. To loosen the
screw, turn it in a clockwise direction.
screw, turn it in a clockwise direction.
WARNING: If forward/reverse switch is on the central position, the tool can not
WARNING: If forward/reverse switch is on the central position, the tool can not
be switched on.
be switched on.
: For drilling into stone and masonry. Use masonry drill bits.
: For drilling into stone and masonry. Use masonry drill bits.
200
8
EN