Weed Eater GHT 180 Manual De Instrucciones página 6

STARTING A FLOODED ENGINE
Flooded en_ginescan be started by placing
the ON/OFFswitch in the ON position and the
choke lever in the OFF CHOKE position and
engaging the throttle lock as directed in the
STARTING A COLD ENGINE section; then,
pull the rope to clear the engine of excess
fuel. Starting could require pulling the starter
rope many times dependin _ g on how badly the
unit is flooded, ff the unit still doesn't start, refer
to the TROUBLESHOOTING TABLE or call
1-800-554-6723.
amWARNINL_: Ensure ON/OFF switch
is in the OFF position and disconnect the
spark plug before performing maintenance
except for carburetor adjustments.
GENERAL RECOMMENDATIONS
Thewarrantyon this unit does not cover items
that have been sub ected to operator abuse
or neg gence. To receve fu va ue from the
warranty, the operator must maintain unit as
instructed in this manual. Various adjust-
ments will need to be made periodically to
properly maintain your unit.
CHECK FOR LOOSE
FASTENERS AND PARTS
• Spark Plug Boot
• Air Filter
• Housing Screws
CHECK FOR DAMAGED OR
WORN PARTS
Contact an authorized service dea_er for re*
placement of damaged or worn parts.
• ON/OFF Switch - Ensure ON/OFF switch
functions properly by moving the switch tothe
OFF position. Make sure engine stops; then
restart engine and continue.
• FuelTank - Do not use unit if fuel tank shows
signs of damage or leaks.
INSPECT AND CLEAN UNIT AND
LABELS
• Before and after each use, inspect corn*
plefe unit for loose or damaged parts. After
each use, clean the unit and labels using a
damp cloth with a mild detergent.
• Wipe off unit with a clean dry cloth.
CLEAN AIR FILTER
Air Filter
Cover
Air Filter
Screw
Cleaning the air filter:
A dirty air filter decreases engine perform_
ance and increases fuel consumption and
harmful emissions. Always clean after every
5 hours of operation.
1. Clean the cover and the area around it to
keep debris from falling into the carburetor
chamber when the cover is removed.
2. Remove parts as illustrated.
NOTE: Do not clean filter in gasc_ineor other
flammable sdvent. Doing so can create a fire
hazard or produce harmful evaperative emis-
sions.
3. Wash the filter in soap and water.
4. Allow filter to dry.
5. Add a few drops of oil to the filter; squeeze
filter to distribute oil.
6. Replace parts.
INSPECT MUFFLER AND SPARK
ARRESTING SCREEN
NOTE: THE SPARK ARRESTING SCREEN
ON THIS UNiT iS NOT SERVICEABLE.
For normal homeowner use, the muffler and
spark arresting screen will not require any ser-
vice.
After 50 hours of use, we recommend that
your muffler be replaced by an authorized
service dealer.
CARBURETOR ADJUSTMENT
WARNING: Keep others away when
making idle speed ad ustments. The blade
will be moving during most of this procedure.
Wear your protective equipment and observe
all safety precautions. When making adjust-
ments, use a screwdriver short enough to
keep your hands behind the handguard and
away from the blade. After making adjust-
ments, the blade must not move at idle speed.
The carburetor has been carefully set at the
factory. Adjustments may be necessary if you
notice any of the following conditions:
Engine will not idle when the throttle is re-
leased.
• The blade moves at idle.
Keep others away when making idle speed
adjustments. Make adjustments with the unit
resting on a level surface free of debris that
can be caught in the hedge trimmer blade.
Serious in ury to the operator and others can
occur f the carburetor s not propery ad-
justed. Keep all parts of your bcdy away from
the blade and muffler.
Idle Speed Adjustment
AIlow engine,to idle. Ad'ust _ .speed until engine
runs without blade moving (idle too fast) or en-
gine stalling (idle speed too slow).
• Turn idle speed screw clockwise to in-
crease engine speed if engine stalls or dies.
• Turn idle speed screw counterclockwise to
decrease engine speed if the blade moves
at idle.
dm!I, W ARNINL-i: Recheck the idle speed
after each ad ustment. The blade must not
move at d e speed to avo d ser ous n ury to
the operator or others.
-6-