Installation Instructions - Haier EST08XCP Manual De Uso Y Cuidado

CAUTION
There are sharp edges that can cause serious cuts.
When lifting the air conditioner,it is HEAVY. Use 2 peoples to lift.
For New Construction install Haier Wall Sleeve.
Remove old air conditioner and inspect sleeve for the following:
Insallation--Make sure that sleeve is securely installed and in
sound structural condition.
Dimensions--Measure the size to make sure the air conditioner
will fit.
Slope--There should be a rearward slope for condensate to
drain from the rear of the sleeve.
Chece against Fig.A.
Wall Sleeve
REAR
Manufacturer--So the method of installation can be determined.
If the installation and slope are suspect,then removal and
correct installation of a Haier Wall Sleeve,is recommended.
Check the conetents of the accessories supplied with your air
conditioner as shown below:
7
8
9
1
4

INSTALLATION INSTRUCTIONS

to
FRONT
UNIT LEVEL
Fig.A
6
5
4
2
3
Number Part name
1
Wide Top/Bottom Trim Frame
2 Wide Side Trim Frame
Narrow Top/Bottom Trim Frame
3
4 Narrow Side Trim Frame
5
Foam Seal
6 Universal Fit Rear Grille
Wire Bundle
7
8 Tapered Spacer Block
9 Board
How to install
Nu r
1.Identify the existing wall sleeve before installing the unit
nch Ma c e l r
from the listed below.
l a l p t la
Wall Sleeve Dimensions(inches)
Brand
m l d ura de
3
Width
Haier Amana
Es re mo dura de
25-13/32
Haier Amana 5
25-7/8
Jun ética d
White-westinghouse
6
P il er uni
Frigidaire
25-1/2
Carrier(52F series)
Torni lo
7
General Electric /Hotpoint 26
d
Whirlpool 25-7/8
i
27
10 Panel
Fedders/Eme son
25-7/8
Sears/Kenmore
Carrier(51S series)
25-3/4
Emerson/Fedders 26-3/4
27
Friedr ch Numbe t
25-7/8
LG
arge a e de a ga nitur du aut/Bas
Note:All wall sleeves used to mount the new Air Conditioner
must be in sound structural condition and have a rear grille
2 arge Cad e d a garn tu e de o
that securely attaches to sleeve,or rear flange that serves as a
im ns one de a caja de monta e(plugadas
M rca
Etroit Cadre d
stop for the Air cond tioner
2.Clean the interior of the sleeve (do not disturb seals).
E oit Ca e d la garn r d ot
m na
H i
25
3.Repaint the sleeve if needed.
5
Sce lant e mousse
4.For best performance and energy efficiency, replace the existing
H ier Amana 25-7 8
rear louver grille with the plastic mesh supplied in the package.
te westi g us
6 Gr le arr ère n verse le
Measure and cut the plastic grille to fit and place inside the wall
r gida e
25 /2
sleeve against the rear flange. See Fig B
r
QTY.
2
2
2
2
1
1
4
2
1
a t ri r i r
2
supe or i n e
2
Depth
Height
2
arte late
15-3/4 17-1/2
15-9/16 16-3/4
1
ma
al
1
16,17-1/2
15-1/4
or 22
16-7/8
15-5/8
17-1/8
16-1/2
16-3/4
16-3/4 1
or 19-3/4
15-17/32 16-23/32
16-7/8 18-5/8
15-3/4 15
16-3/4
16-3/4 Q Y
15-17/32 16-23/32
2
2
16-3/
5-9/16
1
16 7- /
1 -