Skil F0154285 Serie Manual Original página 10

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 32
e) maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the
power tool's operation. If damaged, have the power
tool repaired before use. Many accidents are caused
by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
5) SERVICE
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
SAFETY INSTRUCTIONS FOR JIG SAWS
ELECTRICAL SAFETY
• Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool
• Never use the tool when cord is damaged; have it
replaced by a qualified person
• If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
• Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
PERSONAL SAFETY
• Do not work materials containing asbestos (asbestos
is considered carcinogenic)
• This tool should not be used by people under the age of
16 years
• The noise level when working can exceed 85 dB(A); wear
ear protection
• Wear protective goggles when working with materials
which produce chips
• Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wear a dust mask and work with a dust
extraction device when connectable
• Certain kinds of dust are classified as carcinogenic (such
as oak and beech dust) especially in conjunction with
additives for wood conditioning; wear a dust mask and
work with a dust extraction device when connectable
• Follow the dust-related national requirements for the
materials you want to work with
• Always disconnect plug from power source before
making any adjustment or changing any accessory
BEFORE USE
• Check the functioning of the tool before each use and, in
case of a defect, have it repaired immediately by a
qualified person; never open the tool yourself
• Remove all obstacles on top of as well as underneath the
cutting path before you start cutting
• Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
• Use clamps or another practical way to secure and
support the workpiece to a stable platform (holding
the workpiece by hand or against your body leaves it
unstable and may lead to loss of control)
DURING USE
• Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord (cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live" and
could give the operator an electric shock)
• Always keep the cord away from moving parts of the tool;
direct the cord to the rear, away from the tool
• In case of electrical or mechanical malfunction,
immediately switch off the tool and disconnect the plug
• Keep hands away from the saw blade while the tool is in
use
ACCESSORIES
• SKIL can assure flawless functioning of the tool only
when original accessories are used
• Do not use a saw blade which is cracked, deformed or
dull
OUTDOOR USE
• When used outdoors, connect the tool via a fault current
(FI) circuit breaker with a triggering current of 30 mA
maximum, and only use an extension cord which is
intended for outdoor use and equipped with a
splashproof coupling-socket
AFTER USE
• When you put away the tool, switch off the motor and
ensure that all moving parts have come to a complete
standstill
EXPLANATION OF SYmBOLS ON TOOL
3 Read the instruction manual before use
4 Double insulation (no earth wire required)
5 Do not dispose of the tool together with household waste
material
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
• If for any reason the old plug is cut off the cord of this tool,
it must be disposed of safely and not left unattended
USE
• On/off 6
• Switch locking for continuous use 7
• Changing saw blades 8
! insert blade to full depth with teeth facing forward
9
• Sawing at 15°/30°/45° 0
• Dust suction !a
! do not use vacuum cleaner when cutting metal
• Dust blowing !b
• Operating the tool
- before switching on the tool, ensure that front end of
footplate rests flat on the workpiece
- hold tool firmly with both hands, so you will have full
control of the tool at all times
10

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

4285

Tabla de contenido