Battery Charger Safety - Triton T20 DD Instrucciones De Uso

performed. Use of the power tool for operations different from those intended could
result in a hazardous situation.
Battery tools use and care
a) Recharge only with charger specified by the manufacturer. A charger that is sutiable
for one type of battery pack may create a risk of fire when used with another battery
pack.
b) Use power tools only with specifically designated battery packs.
Use of any other battery packs may create a risk of injury and fire
c) When battery pack is not in use, keep it away from other metal objects, like paper
clips, coins, keys, nails, screws and other small metal objects that can make a
connection from one terminal to another. Shorting the battery terminals together may
cause a burns or a fire.
d) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water. If liquid contact eyes, additionally
seek medical help. Liquid ejected from the battery may cause irritation or burns
WARNING: When used in Australia or New Zealand, it is recommended that this tool is ALWAYS
supplied via Residual Current Device (RCD) with a rated residual current of 30mA or less.
Service
a) Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
Additional Safety for Battery-
Operated Screwdrivers
For safety relating to protective clothing/equipment and general health hazards relating to
power tools; refer to General and Electrical Safety sections in this manual
• Hold power tools by insulated gripping surfaces, when performing an operation where
the cutting accessory may contact hidden wiring. Cutting accessory and/or fasteners
contacting a "live" wire may make exposed metal parts of the power tool "live" and give
the operator an electric shock.
Important: It is imperative to follow all national safety regulations concerning installation,
operation and maintenance
• Do not allow anyone under the age of 18 years to use this tool, and ensure that operators
are qualified and familiar with the operating and safety instructions
• If batteries are to be charged outdoors, ensure that the power supply and charger are
protected against weather/moisture
• Use metal and voltage detectors to locate concealed electric, water or gas lines. Avoid
touching live components or conductors
• Ensure that the lighting is adequate
• Do not put pressure on the tool, to do so would shorten its service life
• Where possible, use clamps or a vice to hold your work
• Examine the chuck regularly for signs of wear or damage. Have damaged parts repaired
by a qualified service centre
• Periodically check all nuts, bolts and other fixings and tighten where necessary

Battery Charger Safety

Use the battery charger correctly
• Refer to the section of this manual relating to use of the battery charger before attempting
to charge the battery.
• Do not attempt to use the charger with any batteries other than those supplied. Keep your
battery charger clean; foreign objects or dirt may cause a short or block air vents. Failure
to follow these instructions may cause overheating or fire
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent
or similarly qualified persons in order to avoid a hazard
• Examine the battery charger regularly for damage, especially the cord, plug and enclosure.
If the battery charger is damaged, it must not be used until it has been repaired
• Children should be supervised to ensure that they do not play with the appliance
Warning: Do not recharge non-rechargeable batteries
Use batteries correctly
• Only charge batteries using the charger provided. Only use batteries provided with this
power tool, or others recommended by the supplier. Keep batteries clean; foreign objects
or dirt may cause a short. Allow batteries to cool for 15 minutes after charging or heavy
use. Failure to follow these instructions may cause overheating or fire.
• When not in use batteries should be stored at room temperature (approx. 20˚C). Ensure
that batteries cannot accidentally short in storage.
NOTICE for Battery Packs
• DANGER – Risk of battery packs include burn hazard, fire hazard and explosion hazard
• CAUTION - Do Not Open, Disassemble, Crush, Heat above 60 degree C or incinerate. Do
Not dispose of in fire or similar.
• CAUTION – for Primary batteries, do not charge.
• CAUTION – only charge battery with charger model T20BC. For Safety use of battery
charger, make reference to the instruction manual of the battery charger.
• CAUTION - Follow Manufacturer's Instructions
Battery and charger safety features
The battery and charger are fitted with a number of safety features which may be triggered
during charging or operation:
• Over-charge protection: Charger automatically switches off when the battery has reached
full charge capacity, protecting the internal components of the battery
• Over-discharge protection: Prevents the battery from discharging beyond the
recommended lowest safety voltage
• Over-heat protection: Sensor switches off if the battery becomes too hot during operation.
This can happen if the tool is overloaded or being used for extended periods of time. Up to
30 minutes cooling time may be required depending on the ambient temperature
• Overload protection: Battery temporarily stops if it is overloaded or the maximum current
draw is exceeded, protecting the internal components. The battery will resume normal
operation when the current draw returns to a normal safe level. This may take a few
seconds
• Short circuit protection: The battery will stop working immediately if a short circuit occurs,
this prevents damage to the battery or tool
WARNING for Australia and New Zealand
WARNING When used in Australia or New Zealand, it is recommended that this tool is ALWAYS
supplied via Residual Current Device (RCD) with a rated residual current of 30mA or less.
GB
5