Skil 7346 Manual Original página 6

f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.,
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5) SERVICE
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
SAFETY INSTRUCTIONS FOR SANDERS
• Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
• Always keep the cord away from moving parts of the tool;
direct the cord to the rear, away from the tool
• When you put away the tool, switch off the motor and
ensure that all moving parts have come to a complete
standstill
• Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
• In case of electrical or mechanical malfunction,
immediately switch off the tool and disconnect the plug
• SKIL can assure flawless functioning of the tool only
when original accessories are used
• This tool should not be used by people under the age of
16 years
• The noise level when working can exceed 85 dB(A); wear
ear protection
• If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
• Never use the tool when cord is damaged; have it
replaced by a qualified person
• Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool (tools with
a rating of 230V or 240V can also be connected to a
220V supply)
• This tool is not suitable for wet sanding
• Secure the workpiece (a workpiece clamped with
clamping devices or in a vice is held more securely than
by hand)
• Do not work materials containing asbestos (asbestos
is considered carcinogenic)
• When sanding metal, sparks are generated; do not use
dustbag and keep other persons and combustible
material from work area
• Do not touch the moving sanding sheet
• Do not continue to use worn, torn or heavily clogged
sanding sheets
• Wear protective gloves, safety glasses, close-fitting
clothes and hair protection (for long hair)
• Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wear a dust mask 4 and work with a
dust extraction device when connectable
• Certain kinds of dust are classified as carcinogenic (such
as oak and beech dust) especially in conjunction with
additives for wood conditioning; wear a dust mask 4
and work with a dust extraction device when
connectable
• Follow the dust-related national requirements for the
materials you want to work with
• Always disconnect plug from power source before
making any adjustment or changing any accessory
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
• If for any reason the old plug is cut off the cord of this tool,
it must be disposed of safely and not left unattended
USE
• Mounting of sanding sheet 5
! disconnect the plug
! the dust suction requires the use of perforated
sanding sheets
! perforation in sanding sheet should correspond
with perforation in sanding foot
! replace worn sanding sheets in time
! always use the tool with the total sanding surface
covered with sanding paper
• On/off switch
- switch on/off the tool by pushing switch A 2 forward/
backwards
! before the sanding surface reaches the
workpiece, you should switch on the tool
! before switching off the tool, you should lift it
from the workpiece
• Dust suction 6
- empty dustbag B regularly for optimal dust pick-up
performance
! do not use dustbag when sanding metal
• Holding and guiding the tool 7
! while working, always hold the tool at the
grey-coloured grip area(s)
- guide the tool parallel to the working surface
! do not apply too much pressure on the tool; let
the sanding surface do the work for you
- do not tilt the tool in order to avoid unwanted sanding
marks
- keep ventilation slots C 2 uncovered
APPLICATION ADVICE
• Move the tool in straight movements in line with the grain
- for sanding bare wood surfaces
- for extra fine finishing
• Never use the same sanding sheet for wood and metal
• Recommended sanding sheet grits:
coarse - for removing paint;
for sanding of extremely rough wood
medium - for sanding of rough or plain wood
fine - for smoothing of wood;
for finishing of bare wood;
for smoothing surfaces with old paint
• Use different grit sizes when the working surface is rough:
- start sanding with coarse or medium grit
- finish with fine grit
6