Cooling Down - Black and Decker KR580 Manual De Instrucciones

depth stop and the end of the drill bit is equal to the
length of the screw you will fit. Tighten the side handle.
PREPARING YOUR DRILL FOR OPERATION
Proceed as follows:
Fit the correct accessory for the job.
for large size drill bits use low speeds and for smaller
drill bits use high speeds.
drill switch, the variable speed control or the forward/
reverse switch when your drill is in operation.
@@ @@ @@ @@ PP @@ PP PP PP PP PP PP PP PP PP @@ @@ PP yy PP @@ @@ PP @@ @@ @@ PP @@ @@ @@ PP @@ @@ @@ PP @@ PP PP @@ PP PP PP PP PP PP PP PP PP @@ PP @@ PP PP @@ PP PP @@ @@ PP @@ @@ @@ PP @@ @@ @@ PP @@ @@ @@ PP @@ @@
USING YOUR DRILL
@@ @@ PP @@ PP @@ PP yy @@ PP @@ @@ @@ @@ @@ @@ @@ PP PP @@ PP PP PP @@ @@ @@ PP @@ @@ @@ PP @@ @@ @@ PP @@ @@ PP PP PP @@ PP PP PP @@ PP PP PP @@ PP PP PP @@ PP PP PP @@ PP PP PP @@ PP PP PP @@ PP PP @@ @@ @@ PP @@ @@
@@ PP PP @@ @@ PP PP PP PP PP PP PP PP PP @@ @@ PP yy PP @@ PP PP @@ @@ @@ PP @@ @@ @@ PP @@ @@ @@ PP @@ @@ @@ @@ PP PP PP PP PP PP PP PP PP PP @@ @@ PP @@ PP @@ @@ PP @@ @@ @@ PP @@ @@ @@ PP @@ @@ @@ PP @@ PP @@ PP @@
PP PP PP PP PP PP PP @@ yy PP PP PP PP PP PP PP PP PP PP PP @@ PP @@ PP @@ PP @@ @@ @@ PP @@ @@ @@ PP @@ @@ @@ PP @@ @@ @@ PP @@ PP @@ PP @@ @@ @@ PP @@ @@ @@ PP @@ PP @@ @@ @@ @@ @@ PP @@ PP @@ PP @@ @@ PP PP @@ PP @@
continuous, depress the switch again and release.
While your drill is in operation, do not touch the chuck.
HANDY HINTS
• Fit the correct size and type of drill or screwdriver bit.
• Always hold your drill using the handle and the
side handle.
KR580-700 ML p21-35
• Always hold your drill at right-angles to your work.
Set the speed of
your drill by
setting the
variable speed
control to the
hammer mode
desired position.
hammer/drill switch to the drill mode
As a general rule,
• Set the forward/reverse switch to the correct direction.
• Never change the direction of rotation when your
drill is in operation.
Set the forward/
• After use, remove the drill bit and gently tap the side
reverse switch to
of the chuck with a soft-faced hammer to remove
the desired
the dust. This will extend the life of the chuck.
direction of
rotation. Never

COOLING DOWN

change the setting If your drill becomes too hot in use, set the variable
of the hammer/ speed control to its highest setting and allow your drill
to operate without load for 2 minutes.
OVERLOAD
Never use excessive force when using your drill. Too
much pressure can reduce the speed of your drill and
To switch your
reduce its efficiency. This can result in an overload
drill on, depress
which can cause damage to the motor of your drill.
the on/off switch.
Your drill stops
EC DECLARATION OF CONFORMITY
when the switch
We declare that units: KR580RE, KR580CRE, KR650RE,
is released.
KR650CRE, KR700RE, KR700CRE conform to 98/37/EC,
89/336/EEC, EN55014, 73/23/EEC, EN55104, EN50144
A weighted sound pressure 99dB (A)
A weighted sound power 112dB (A)
If continuous
Hand/arm weighted vibration 8.89m/s
operation is
required, depress
the lock-on button
while the on/off
Brian Cooke - Director of Engineering
switch is
Black & Decker Ltd, Spennymoor, County Durham
depressed. To stop
DL16 6JG United Kingdom
your drill when
operation is
The Black & Decker policy is one of continuous
improvement to our product and as such we reserve
the right to change the product specification without
prior notice.
25
ENGLISH
When drilling
B C B C B C B C B C B C B C B C B C R S   R S   B C R S   B C B C B C R S   B C R S   B C B C B C R S   B C B C B C R S   B C B C B C R S   B C B C | R S   R S   B C R S   R S   R S   B C B C R S   R S   B C R S   R S   R S   B C R S   R S   R S   B C R S   R S   R S   B C R S   R S   R S   B C R S   R S   R S   B C R S   R S   R S   B C R S   R S   B C R S    
wood and metal,
set the hammer/
drill switch to the
drill mode
When drilling
masonry, set the
hammer/drill
switch to the
. When screwdriving, set the
.
2
05-02-2001, 10:48
.
25