Product Specifications; Installation Instructions - Homewerks 55-K821S-SS-T Instrucciones De Instalación

PRODUCT SPECIFICATIONS

Maximum Flow Rate: 1.8 GPM (6.814 LPM) at 60 PSI
ASME A112.18.1/CSA B125
NSF/ANSI 61
Stainless steel or matte black finish

INSTALLATION INSTRUCTIONS

1.
Shut off the water at the supply valves under
the sink or at the main water supply. Discon-
nect the supply lines. Remove the existing
faucet from the sink.
Clean and dry the surface area where the
new faucet will be mounted.
2. To install with the optional deckplate for
a 3-hole sink, skip to Step 3.
Remove the pre-assembled lock nut (E) with
hex bolts (G), rubber washer (D) and metal
washer (F) from the shank (2.1) on the faucet
body (A). Before installation, make sure the
flange (2.1) is on the bottom of the faucet
body (A). Pull the black spray hose (2.2) up
through the faucet body (A) until the end of
the hose is flush with the bottom of the shank
(2.3) on the faucet body (A). Do not pull the
fitting on the bottom of the black spray hose
(2.2) past the shank. Carefully insert the
integrated supply lines and tubes (2.4) on the
faucet body (A) through the mounting hole in
the sink (2.5). Skip to Step 4.
NOTE: Do not feed the spray hose (2.2) back
down through the faucet body (A) until Step 5.
3. Optional deckplate installation:
The optional deckplate (B) and gasket (C)
cannot be installed with the flange.
Apply a thin bead of silicone to the
underside of the gasket (C). Place the gasket
(C) and deckplate (B) over the mounting
holes in the sink, aligning the center hole in
the gasket (C) and deckplate (B) with the
center mounting hole in the sink (3.1). Pull
the black spray hose (3.2) up through the
faucet body (A) until the end of the hose is
flush with the bottom of the shank (3.3) on
the faucet body (A). Do not pull the fitting
on the bottom of the black spray hose
(3.2) past the shank. Carefully insert the
integrated supply lines and tubes (3.4) on
the faucet body (A) through the hole in the
deckplate (B) and the mounting hole in the
sink (3.1) until the faucet sits on top of the
deckplate (B).
NOTE: Do not feed the spray hose (3.2)
back down through the faucet body (A)
until Step 5.
4. From underneath the sink, secure the
faucet body (A) to the sink using the rubber
washer (D), metal washer (F), and lock
nut (E). Secure the lock nut (E) with the
hex bolts (G). NOTE: It is helpful to have
a second person hold the faucet in place
while tightening the bolts on the lock nut.
HomewerksWW.com
1
2
A
2.1
2.3
2.5
2.4
D
F
E
G
2.2
3
A
B
C
3.1
D
F
G
E
3.2
4
A
D
F
E
G
Ceramic cartridge
Manufactured to include no more than 0.25% weighted average lead content
on wetted surfaces
Total weight of item: 4.74 lbs.
5. Attach the top of the control box (H) to
the shortest braided line (5.1) coming
from the faucet body (A). Feed the black
spray hose (5.2) back down through the
spout and faucet body (A) and through
the hole in the sink. Then attach the
bottom of the control box (H) to the
black spray hose (5.1).
After the black spray hose (5.2) is
connected, attach the weight (J) to the
hose (5.2) at the location indicated. Push
the "Open" tab down to open the two
sides of the weight (J). Snap the two sides
of the weight (J) back together around
the black spray hose (5.2).
6. Attach the power connector (I), which
houses the batteries, to the control box
(H). Insert four AA batteries (not
included) into the battery holder (6.1).
7. Attach the end of the hot water (red
stripe) and cold water (blue stripe) supply
lines coming from the faucet body (A) to
the hot and cold water supply valves (7.2)
under the sink, after making sure the
supply valves (7.2) are clear of any debris.
Thread the nut on the end of the
integrated supply line (7.1) onto the
outlet of the water supply valve (7.2) and
tighten with a wrench. Do not overtighten.
NOTE: Do not use PTFE pipe tape,
plumber's putty, pipe dope, or any other
type of sealing compound on the water
inlets or threads. Additional compound is
not necessary. A watertight seal between
the supply valve and the nut on the
integrated supply line is achieved by
compression.
8. To install the optional soap dispenser,
unscrew the top of the soap dispenser (K)
from the plastic soap bottle and remove
the mounting nut (8.1) and rubber gasket
(8.2). From above the sink, insert the top of
the soap dispenser into the fourth hole
opening in the sink. From underneath the
sink, place the rubber gasket (8.2) onto the
shank (8.3) on the soap dispenser (K) and
then thread the mounting nut (8.1) onto
the shank (8.3) to secure the soap
dispenser (K) to the sink.
2
5
5.1
H
J
5.2
6
6.1
H
I
7
7.1
7.2
8
K
8.3
8.2
8.1