Technical Data - Blooma Nashua 7700511425 Instrucciones

Safety
These instructions are for your safety. Please read through
them thoroughly prior to installation and retain them for future
Safety
reference.
These instructions are for your safety. Please read through
accordance with local regulations (IET wiring regulation
them thoroughly prior to installation and retain them for future
BS7671).
reference.
Check the pack and make sure you have all of the parts listed.
Remove all packaging, wrap etc. from the product.
accordance with local regulations (IET wiring regulation
Decide on the appropriate location for your product.
BS7671).
CAUTION: IP67 & IP65 is guaranteed when the product is
Check the pack and make sure you have all of the parts listed.
properly installed and sealed.
Remove all packaging, wrap etc. from the product.
Always avoid the product to be located at corrosive environment.
Decide on the appropriate location for your product.
Always refer to the installation drawing for the orientation of the
CAUTION: IP67 & IP65 is guaranteed when the product is
product.
properly installed and sealed.
Maximum temperature of contact: 100°C. Intended for use
Always avoid the product to be located at corrosive environment.
in pedestrian or cycling zones. Acceptable static load: 5kN.
Always refer to the installation drawing for the orientation of the
Caution: Do not let plants grow close to the lamp.
product.
Wiring diagram is for reference only. Always refer to the terminal
Maximum temperature of contact: 100°C. Intended for use
marking for wiring. Ensure that all electrical connections are tight
in pedestrian or cycling zones. Acceptable static load: 5kN.
and that no loose strands are left out of the terminal block.
Caution: Do not let plants grow close to the lamp.
When the product does not light after installation:
Wiring diagram is for reference only. Always refer to the terminal
> Ensure there is no electricity failure
marking for wiring. Ensure that all electrical connections are tight
> Ensure all the connections are secured
and that no loose strands are left out of the terminal block.
If you have any doubt about installation / use of this product,
When the product does not light after installation:
> Ensure there is no electricity failure
Always disconnect the product from mains at least 10 minutes
> Ensure all the connections are secured
allowing to cool down before any maintenance or adjustment.
If you have any doubt about installation / use of this product,
It is recommended to have a regular schedule of care and
maintenance to keep the surface condition well.
Always disconnect the product from mains at least 10 minutes
allowing to cool down before any maintenance or adjustment.
It is recommended to have a regular schedule of care and
maintenance to keep the surface condition well.
Warranty Period and Conditions
At Blooma, we devote special attention to selecting high-quality materials and use manufacturing techniques that enable us to create
designer and durable product ranges.
Warranty Period and Conditions
That is why we offer a 2-year warranty against product manufacturing defects. This product is under warranty for 2 years as from the date of
purchase, for normal, non-professional household use.The warranty shall only apply upon presentation of the till receipt or the invoice. Keep
At Blooma, we devote special attention to selecting high-quality materials and use manufacturing techniques that enable us to create
your proof of purchase in a safe place.
designer and durable product ranges.
The warranty covers product breakdowns and malfunctions under the condition that the product is used in accordance with its intended use
That is why we offer a 2-year warranty against product manufacturing defects. This product is under warranty for 2 years as from the date of
and subject to installation and maintenance in accordance with good practice and the information contained in the user's manual.
purchase, for normal, non-professional household use.The warranty shall only apply upon presentation of the till receipt or the invoice. Keep
This product must be installed so that it may be later removed without damaging it.
your proof of purchase in a safe place.
This contractual warranty does not cover defects and damage caused by the natural wear of parts, bad weather
The warranty covers product breakdowns and malfunctions under the condition that the product is used in accordance with its intended use
freezing, damage caused by water quality (hardness, aggressiveness, corrosion, etc.), by the presence of foreign bodies transported by
and subject to installation and maintenance in accordance with good practice and the information contained in the user's manual.
This product must be installed so that it may be later removed without damaging it.
negligence, accident or maintenance that is defective or does not comply with good practice or the information in the user's manual.
This contractual warranty does not cover defects and damage caused by the natural wear of parts, bad weather
The following are also excluded from the warranty: harmful consequences due to the use of accessories and/or non-original equipment
freezing, damage caused by water quality (hardness, aggressiveness, corrosion, etc.), by the presence of foreign bodies transported by
The warranty is limited to those parts recognised as defective. Under no circumstances shall it cover fringe expenses (travel, labour) and
negligence, accident or maintenance that is defective or does not comply with good practice or the information in the user's manual.
direct and consequential damage.
The following are also excluded from the warranty: harmful consequences due to the use of accessories and/or non-original equipment
This guarantee is in addition to and does not affect your statutory rights.
The warranty is limited to those parts recognised as defective. Under no circumstances shall it cover fringe expenses (travel, labour) and
direct and consequential damage.
This guarantee is in addition to and does not affect your statutory rights.
3663602892878-Blooma-A5-IM-V03.indb 3

Technical Data

Supply Voltage: 220-240 V~, 50 Hz
Technical Data
1 x Max. 11 W CFL or LED (11 W) GU10
Bulb Type: (check bulb dimensions in relation to space
available)
Supply Voltage: 220-240 V~, 50 Hz
This product complies with conformity
1 x Max. 11 W CFL or LED (11 W) GU10
Conformity with all relevant EC Directive
requirements of the applicable
Bulb Type: (check bulb dimensions in relation to space
requirements.
European Regulations or Directives.
available)
This product complies with conformity
Class I product, must be connected to Conformity with all relevant EC Directive
requirements of the applicable UK
requirements. earth.
Regulations.
IP65
Jet-proof.
Class I product, must be connected to
earth.
IP67
Water tight: temporary immersible up
to 1m
IP65
Jet-proof.
Waste electrical products should not be
disposed of with household waste. Please
IP67
Water tight: temporary immersible up
recycle where facilities exist. Check with
to 1m
your Local Authority or local store for
Waste electrical products should not be
recycling advice.
disposed of with household waste. Please
xxWyy xx-year; yy-week of the year
recycle where facilities exist. Check with
your Local Authority or local store for
recycling advice.
xxWyy xx-year; yy-week of the year
Light source replaceable by an end-user.
This product contains a light source of energy efficiency
class E
30/10/2017 16:37