Black and Decker REVDD12C Traducción De Las Instrucciones Originales página 6

ENGLISH
Injuries caused by touching any rotating/moving parts.
u
Injuries caused when changing any parts, blades or
u
accessories.
Injuries caused by prolonged use of a tool. When using
u
any tool for prolonged periods ensure you take regular
breaks.
Impairment of hearing.
u
Health hazards caused by breathing dust developed when
u
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured in
accordance with a standard test method provided by EN62841
and may be used for comparing one tool with another.
The declared vibration emission value may also be used in a
preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Labels on tool
The following pictograms along with the date code are shown
:
on the tool:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
Additional safety instructions for batteries and
Batteries
Never attempt to open for any reason.
u
Do not expose the battery to water.
u
Do not store in locations where the temperature may
u
exceed 40 °C.
Charge only at ambient temperatures between 10 °C and
u
40 °C.
Charge only using the charger provided with the tool.
u
When disposing of batteries, follow the instructions given
u
in the section "Protecting the environment".
Do not attempt to charge damaged
batteries.
6
(Original instructions)
Electrical safety
#
Your charger is double insulated; therefore no
earth wire is required. Always check that the
mains voltage corresponds to the voltage on
the rating plate. Never attempt to replace the
charger unit with a regular mains plug.
If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Warning! Never attempt to replace the charger unit with a
regular mains plug.
Features
This tool includes some or all of the following features:
1. Variable speed switch
2. Forward/reverse slider
3. Torque adjustment collar
4. Keyless chuck
5. Charger
5a. Charging port
5b. Charging indicator (not visible till plugged in)
Charging the battery (fig. A)
The integral battery needs to be charged before first use and
whenever it fails to produce sufficient power on jobs that were
easily done before. The battery may become warm while
charging; this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging
temperature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 10 °C or above 40 °C.
The integral battery should be left connected to the charger
and the charger will begin to charge automatically when the
cell temperature warms up or cools down.
Insert the charging connector (5) into the charging port
u
(5a).
Plug in the charging connector (5).
u
Leave the tool connected to the charger for around 4
u
hours.
The charging indicator (5b) will illuminate during charging.
u
Operating Instructions
Trigger switch & reversing button (fig. B, C)
The drill is turned ON and OFF by pulling and releasing
u
the trigger switch (1).
The farther the trigger is depressed, the higher the speed
of the drill operates at.
A forward/reverse control button (2) determines the direc-
u
tion of the tool and also serves as a lock off button.