Transportation And Handling; Important - GGP ITALY SPA 325 Manual De Instrucciones

SAFETY REQUIREMENTS
ground that does not guarantee stability for the
operator;
– never run, but walk carefully paying attention to
the lay of the land and any eventual obstacles;
– assess the potential risks of the ground to be
mown and take all necessary precautions to
ensure your own safety, especially on slopes or
on bumpy, slippery or unstable ground;
– work along the contour on slopes, never when
walking up or down and always keep downhill
of the cutter.
4) Make sure the machine is securely locked
when you start the engine:
– start the motor in an area at least 3 metres from
where you refuelled;
– check that there is nobody within at least 15
metres of the machine's range of action or at
least 30 metres for heavier mowing;
– do not direct the silencer and therefore the
exhaust fumes towards inflammable materials.
5) Do not change the engine governor settings
or overspeed the engine.
6) Do not strain the machine too much and do not
use a small machine for heavy-duty works. If you
use the right machine, you will reduce the risk of
hazards and improve the quality of your work.
7) Check that when the machine is running idle,
there is no movement of the cutting device and,
after pressing the throttle trigger, the engine
quickly returns to minimum speed.
8) Ensure that the blade does not come into vio-
lent contact with foreign bodies and beware of the
possibility of material being thrown up by the
blades.
9) Always keep the machine connected to the
webbing when working.
10) Stop the engine:
– whenever you leave the machine unattended.
– before refuelling.
– during movements between work areas.
11) Stop the engine and disconnect the spark
plug cable:
– before cleaning, checking or working on the
machine;
– after striking a foreign object. Inspect the
machine for any damage and make repairs
before restarting it again;
– If the machine starts to vibrate abnormally: find
and remove the cause of the vibration immedi-
ately;
– when the machine is not in use.
D) MAINTENANCE AND STORAGE
1) Keep all nuts, bolts and screws tight to be sure
the equipment is in safe working condition.
Routine maintenance is essential for safety
and for maintaining a high performance level.
2) Do not store the machine with fuel in the tank
in an area where the fuel vapours could reach an
open flame, a spark or a strong heat source.
3) Allow the engine to cool before storing in any
enclosure.
All manuals and user guides at all-guides.com
4) To reduce fire hazards, keep the engine,
exhaust silencer and fuel storage area free from
sawdust, branches, leaves, or excessive grease;
never leave containers with the cut debris inside
the storage area.
5) If the fuel tank has to be emptied, this should
be done outdoors once the engine has cooled
down.
6) Always wear protective gloves when handling
the cutting device.
7) For safety reasons, never use the machine
with worn or damaged parts. Damaged parts
are to be replaced and never repaired. Only
use original spare parts. Parts that are not of the
same quality can seriously damage the equipment
and compromise safety. The cutting tools must
always bear the manufacturer's trademark as well
as a reference to the maximum working speed.
8) Before putting the machine away, check you
have removed wrenches or tools used for mainte-
nance.
9) Store the machine out of the reach of children!
E) TRANSPORTATION AND HANDLING
1) Whenever the machine is to be handled or
transported you must:
– turn off the engine, wait for the cutting device to
– fit the cutting device guard;
– only hold the machine using the handgrips and
2) When using a vehicle to transport the machine,
position it so that it can cause no danger to per-
sons and fasten it firmly in place to avoid it from
tipping over, which may cause damage or fuel
spillage.
F) HOW TO READ THE MANUAL
Certain paragraphs in the manual contain particu-
larly significant information and are marked with
various levels of highlighting with the following
meaning:
or
information on what has already been said, in the
aim to prevent damage to the machine.
sult in the risk of injury to oneself or others.
sult in the risk of serious injury or death to
oneself or others.
stop and disconnect the spark plug cap;
position the cutting device in the opposite
direction to that used during operation.
NOTE

IMPORTANT

These give details or further
WARNING!
Non-observance will re-
DANGER!
Non-observance will re-
5
EN