Dolby Surround - Denon AVR-2106 Instrucciones De Operación

Ocultar thumbs Ver también para AVR-2106:
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 220
Additional Information
[2] When not using surround back speakers
Front speakers
Center speaker
Monitor
Subwoofer
60°
120°
Surround speakers
[ As seen from above ]
Surround speaker
Front speaker
60 to 90 cm
[ As seen from the side ]
• Set the front speakers with their front surfaces as flush with
the TV or monitor screen as possible. Set the center speaker
between the front left and right speakers and no further from
the listening position than the front speakers.
• Consult the owner's manual for your subwoofer for advice on
placing the subwoofer within the listening room.
• If the surround speakers are direct-radiating (monopolar), then
place them slightly behind and at an angle to the listening
position and parallel to the walls at a position 60 to 90 cm above
ear level at the prime listening position.
Surround
The AVR-2106 is equipped with a digital signal processing circuit
that lets you play program sources in the surround mode to
achieve the same sense of presence as in a movie theater.

[1] Dolby Surround

q
Dolby Digital
Dolby Digital is the multi-channel digital signal format
developed by Dolby Laboratories.
Dolby Digital consists of up to "5.1" channels – front left,
front right, center, surround left, surround right, and an
additional channel exclusively reserved for additional deep
bass sound effects (the Low Frequency Effects –LFE–
channel, also called the ".1" channel, containing bass
frequencies of up to 120 Hz).
Unlike the analog Dolby Pro Logic format, Dolby Digital's main
channels can all contain full range sound information, from the
lowest bass, up to the highest frequencies – 22 kHz. The
signals within each channel are distinct from the others,
allowing pinpoint sound imaging, and Dolby Digital offers
tremendous dynamic range from the most powerful sound
effects to the quietest, softest sounds, free from noise and
distortion.
2 Dolby Digital and Dolby Pro Logic
Comparison of home
Dolby Digital
surround systems
No. of recorded
5.1 ch
channels (elements)
No. of playback
5.1 ch
channels
Playback channels
L, R, C, SL, SR, SW
(max.)
Digital discrete
processing Dolby
Audio processing
Digital encoding /
decoding
High frequency
playback limit of
20 kHz
surround channel
50
ENGLISH
2 Dolby Digital compatible media and playback
methods
Symbol indicating Dolby Digital compatibility:
The following are general examples. Also refer to the player's
operating instructions.
Media
LD (VDP)
DVD
Others
(satellite broadcasts,
CATV, etc.)
1: Please use a commercially available adapter when
connecting the Dolby Digital RF output terminal of the LD
player to the digital input terminal.
Please refer to the instruction manual of the adapter when
making connection.
2: Some DVD digital outputs have the function of switching
the Dolby Digital signal output method between
Dolby Pro Logic
"bitstream" and "(convert to) PCM". When playing in
Dolby Digital surround on the AVR-2106, switch the DVD
player's output mode to "bitstream". In some cases
2 ch
players are equipped with both "bitstream + PCM" and
"PCM only" digital outputs. In this case connect the
"bitstream + PCM" terminals to the AVR-2106.
4 ch
w
Dolby Pro Logic
L, R, C, S
• Dolby Pro Logic
(SW – recommended)
developed by Dolby Laboratories using feedback logic steering
technology and offering improvements over conventional Dolby
Analog matrix
Pro Logic circuits.
processing Dolby
• Dolby Pro Logic
Surround
recorded in Dolby Surround (
into five channels (front left, front right, center, surround left
and surround right) to achieve surround sound.
7 kHz
ENGLISH
Additional Information
Dolby Digital output
Playback method
terminals
(reference page)
Coaxial Dolby Digital
Set the input mode to
RF output terminal
"AUTO"
(
page 18, 19).
1
Optical or coaxial
Set the input mode to
digital output
"AUTO"
(same as for PCM)
(
page 18, 19).
2
Set the input mode to
Optical or coaxial
"AUTO"
digital output
(
page 18, 19).
(same as for PCM)
II
II
is a new multi-channel playback format
II
can be used to decode not only sources
) but also regular stereo sources

Publicidad

Tabla de contenido

Solución de problemas

loading

Tabla de contenido