Optional Equipment - Jotul FS 120 Instrucciones De Instalación

eNglish
4.0 Installation
Note! The product is heavy. Make sure you have help when
lifting it.
4.1 Preparation/installation
NB: the cast iron legs are not to be used.
1. Place the cardboard packaging on the floor and lay the insert
carefully down on its back.
. Assemble the heat shield under the base of the fire with
the aid of 1 collar head screw (M6x10mm) which is fastened
under the base plate.
3. Place the steel plate (fig. 5 - 900925) under the insert so
that the bolts in the insert pass through the plate. Secure
them on the underside with nuts. The two holes in the plate
should face forwards.
4. Make sure to have assistance and lift the product carefully
up.
4.2 Installation of the soap stone
surround
Necessary tools: Spirit level, tape measure, hammer, rubber
hammer, sheet metal shears.
Remember that the stones can easily be damaged if they are
not handled with care.
If the surface becomes scratched, it can be polished with fine
sandpaper. Deeper scratches can be repaired by filling the scratch
with a paste made from soap stone powder and water glass.
1. Decide where the fireplace will stand (in relation to the
chimney). Flooring within the surround must be covered by
a steel plate (minimum thickness 0.9 mm) if the fireplace is
to stand on a floor of combustible material.
Note! The underlay must be completely level. Max. 2
mm/m tolerance. This is very important for the rest of the
installation process.
. Lay out all the stones carefully following the numbering of
the stones as shown in figure 1C.
3. First lay out the stones for layer 1. (Z88-Z94-Z92-Z88).
4. Make sure that all the stones are level. If necessary use
small pieces of steel or cement to adjust the height of the
stones.
5. Attach the side to the front stone with the help of clamps
(900031).
6. Use a hammer to attach the mounting pieces. See fig. 2
(900038). Be careful not to split the stones when hammering
in the clamps.
7. Attach the steel plate to the back with the clips (900286).
(Check that the airway at the bottom of the heat shield is
removed).
8. Lay the stones for layer  (Z96-Z93-Z93-Z95) and hammer in
the clips – also to the screen plate behind. (See fig. 4).
9. Position the lower shelf (Z97). Secure it in the corners with
clamps (see fig. 4).
10. Position the plate (with the insert in) in the cut-out in the
side stones (fig. 5).
11. Position the smoke bend and measure where the hole for the
chimney is to be placed and adjust the smoke pipes.
1. Remove the insert before carrying out the preparations
necessary in order to attach the smoke pipe guide, smoke
pipe and smoke bend.
8
All manuals and user guides at all-guides.com
13. Lay the 3
14. Lay the 4
15. Install the two steel plates (900040) on the inside of the
16. Attach the shelf to the side pieces with clamps (900031) and
17. Attach the smoke pipe to the chimney.
18. Lay the 5
19. Attach the spacers (900287-900288) see fig. 9 and position
0. Place the top grate and top plate (Z99-Z63). See fig. 10.
4.3 Steel Chimney
If a topmounted steel chimney is to be used, install the start
flue pipe in the insert's top smoke outlet. Then assemble the
steel chimney in accordance with its installation and operating
instructions.

5.0 Optional equipment

Front elements in rough structure
The two uppermost stones can be replaced with a front element
in the rough structure - cat. nr. 350769
Stone for side flue
If a side flue is to be used stones can be supplied with appropriate
holes.
Side stone, left - cat.no. 350781
Side stone, right - cat. no. 350780
Floor plate - cat. no 350985
A floor plate is available for your Jøtul FS 120 - I 150 FL. The
dimensions of the plate are: 555x350x1 mm.
layer of side stones (Z64-Z64) – remember the
rd
fixing clips on the stone and the heat shield (see fig. 7).
layer of side stones (Z89-Z89) – remember the
th
fixing clips (see fig. 7).
stone and place the upper shelf on top (Z98).
hammer in the 3 fixing pieces. See fig. 7.
For a rear outlet: A hole must be cut in the heat shield if using
a rear outlet.
For a top outlet: A heat shield (from the insert) has to be
mounted if the wall is made of flammable material. Fix the
heat shield to the rear heat shield by means of two screws
and nuts that you will find in the bag (see fig. 8).
NB. The flue pipe must be attached to the insert before the
top plate is placed on top.
layer of stones (Z91-Z123-Z122-Z90). You should
th
also use the fixing pieces (900038) between the side and
front stones. Ideally silicon should be used between the front
stones.
the grate.