Electrical Installation - Sammic XM-30 Manual De Instrucciones

from someone responsible for their safety and
understand the risks that this implies. Do not allow
children to play with the appliance. The cleaning
and maintenance to be performed by the user must
not be performed by unsupervised children.
• Do not allow comfort or familiarity with the product
(due to using it repeatedly) to substitute strict
compliance with the safety regulations. Stay alert,
pay attention to what you are doing and use
common sense when operating the appliance.
• Do not use the equipment when you are tired or
under the influence of drugs, alcohol or any other
medication. If you use the tool in an unsafe or
incorrect way, you may suffer personal injury or
material damage.
• The models cited in the manual have been
designed for use in hotels, restaurants, catering
and commercial applications.
• The manufacturer is not responsible when the
product is used incorrectly or differently than the
use mentioned above. Such as, sanitary use,
chemical use, use in explosive atmospheres...
• If you wish to use an accessory, it must specifically
be for the model in question and carry the SAMMIC
brand. The user is responsible for any incident
provoked by an accessory that does not carry the
SAMMIC brand.

ELECTRICAL INSTALLATION

The machines are supplied for operation on 230V/50-60Hz/1~ or
120V/50-60Hz/1~. Prepare a single-phase wall-mounted socket with a
residual current and circuit breaker of 10 A.
ASSEMBLY OF THE BLENDER AND MIXER ARM
Picture 10
With the blender unplugged, guide the arm attachment (2) into the
motorised body (1) so that the "arrow" symbol on the arm matches the
"open padlock" symbol on the motor block. Twist the arm clockwise until
the "arrow" matches the "closed padlock" symbol and you notice a "click"
which indicates that it is firmly attached against the restraint system.
To remove, proceed in the opposite manner (10).
ASSEMBLY OF THE MIXER ARM STIRRERS (MODELS
MB AND B)
To assemble, insert the stirrer bushing into the hole in the geared motor
by turning and pushing until it reaches the end. To remove, pull firmly on
the stirrer until it separates from the geared motor.
OPERATION
CONTROLS:
Pilot light (3): This indicates the state of the appliance.
Red light: Machine connected to the mains electricity supply.
Green light: Machine ready to start. It will start when the "On" button
(5B) is pressed.
Multifunction button (5A): Unblock (open padlock) and continuous
operation.
"On" button (5B). Starts the machine, once it has been unblocked and
has a green pilot light.
Introduce the appliance's arm into the container, a maximum of up to
2/3 of the length of the arm, marked with "MAX" (7). Never exceed this
mark. To avoid splashes from entering the motor block, we recommend
that the tilt of the appliance does not exceed 30° (6).
The appliance has a pilot light (3) and when said light is on, this means
that it is connected. Handle the appliance carefully whenever the pilot
light (3) is on.
After connecting the appliance to the power supply:
• With the machine in a vertical position a red pilot light (3), press the
multifunction button (5A) to unblock the machine. The machine is
unblocked for 3 s and the pilot light (3) turns green. If the "On" button
(5B) is not pushed during this 3 s period, the machine blocks out again
and the pilot light (3) changes back from green to red.
• Whenever the pilot light (3) is green, the motor will start every time
the "On" button (5B) is pressed. It will stop as soon as the button is
released and the operator will have 3 s to re-press the button before
the machine blocks out again and the pilot light (3) turns red.
• While holding down the "On" button (5B) and with the motor running,
press the multifunction button (5A) to switch the appliance to
continuous operation mode.
• Press any button (5A, 5B) to stop the machine when running in
continuous operation.
In MB models equipped with a variable-speed drive, the blade's
rotational speed can be changed using the adjustment control (4).
When you have finished using it, always disconnect the plug from the
power supply.
If overheating occurs due to an overload in use, motor blockage... the
thermal protector protects the motor and stops it. Wait for the blender to
cool before turning it on again.
CLEANING AND HYGIENE. WARNINGS
- To avoid electric shocks that can cause serious personal injury, unplug
the appliance before cleaning.
- This appliance is fitted with sharp blades (8). Handle them with care.
- Do not use the following products: abrasive cleaning products (such
as ammonia, bleach, etc.) solvents, metal scourers to scrub, gritty
detergent.
These products may scratch, cut and damage the metal and plastic
surfaces of the appliance.
CLEANING PROCEDURE
Cleaning the blender/beater arm (2), after each use is absolutely
necessary, as well as checking the condition of the lower seals (9). If
you see any signs of deterioration in the seal, contact the authorized
repair service.
After each use, place up to 2/3 of the length of the blender arm in
a recipient containing hot water (35-45 ºC) and switch on for a few
seconds.
The tube and the blade must be washed with hot water (35-40º C) and
an Ivory Liquid type of multi-purpose liquid detergent in a proportion
of 1 measure of detergent per 10 measures of water, leaving them
submerged for 30 minutes. Rinse the soap residues from the stirrers
11
EN