ETI Solid State Lighting 56567241 Manual De Uso Y Cuidado página 3

STEM MOUNTING INSTALLATION
This section is for suspended mounted fixtures only.
Option Installation Accessory Kit Sold Separately
Installing contractor is responsible for determining best installation method for desired location and selecting the appropriate mounting hardware.
Punch out the 2 knock out holes on the fixture that will be used for stem mounting.
5c
Feed all the wires from the electrical box through the knock out hole.
6c
Use the jumper wires to make the electrical connections from the electrical box to the
7c
fixture:
wire to gray wire.
Screw the ceiling plate and stem together, then feed the jumper wires through the
8c
ceiling plate, stem, stem mounting kit bracket and into the electrical box. Reconnect
the terminal ground wire to the wire cover. Reattach the wire cover to the fixture and
make sure to tuck all of the wires inside the wire cover.
Use 2 screws (not included) to secure one of the stem mounting kit bracket (not
9c
included) to the electrical box. Insert two plastic drywall anchors (not included) into
the ceiling and use 2 stem mounting kit screws (not included) to attach the remaining
stem mounting kit bracket (not included) to the ceiling. Make sure the ceiling plate,
stem, and stem mounting kit bracket are secure.
Insert one stem into one of the knock out holes in the fixture and secure the stem with
10c
the stem mounting kit nut (not included). Repeat step with the remaining stem.
Close the lens cover.
11c
Move the locks to the lock position on both ends of the fixture.
12c
Reattach the end caps.
13c
Restore power to the electrical box. Turn the light switch on to activate the fixture.
14c
Turn the light switch off and back on again to activate the direct light only.
Turn the light switch off and back on again to activate the indirect light only.
NOTE: To change between light modes, the light switch has to be turned off and on
within 3 seconds.
CONTINUOUS ROW BRACKET INSTALLATION
NOTE: Multiple light fixtures can be connected, up to a maximum of 8 Lights.
NOTE: If planning to continuously mount multiple fixtures using a single power source, feed the electrical wires from the electrical box through the center of the conduit and then through
the open knock out hole in the fixture.
NOTE: UL LISTED: CCN:FKAV/7 TYPE: 1/2 FOR THREADED COUPLER.(recommended)
Threaded Nut(by others)
Threaded coupler(by others)
H
Punch out the knock out holes at each end of each fixture where the two fixtures
1
will connect.
Remove the end caps and open the lens of each fixture.
2
Insert a 7/8in. outer diameter fitting threaded coupler (not included) through both
3
open knock out holes. Secure the coupler with 2 threaded nuts (not included).
WARNING: Carefully read and understand the information given in this manual before beginning the assembly and installation. Failure to do so could lead to electric shock, fire,
This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
cleaning.
NOTICE:
NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: Reorient or relocate the receiving antenna, increase the separation between the equipment and the receiver, connect the equipment
into an outlet on a circuit different from that to which the receiver is connected, and consult the dealer or an experienced radio/TV.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
See website for Warranty, Troubleshooting or Care and Cleaning details at www.ETiSSL.com.
La versión española está en el
sitio web www.ETiSSL.com.
Questions, problems, missing parts? Call ETiSSL Customer Service 8 a.m. - 5 p.m., CST, Monday - Friday
1-855-ETI-SSLI (1-855-384-7754) www.ETiSSL.com
I
Knock out
hole
D
B
H
Insert one end of the jumper wires into the wire connectors from the first fixture, then
4
run jumper wires through the threaded coupler, and insert the other end into the wire
connectors from the next fixture and make the electrical connections.
Connect the two fixtures to the continuous mounting bracket using the thumb screws.
5
Close the lens. Reattach the end caps and make sure it is secure.
6
K
M
H
N
O
L
A
J