Mains Connection - eisenblatter VARILEX WSF 1800 Manual Original

fi re, no combustible materials should be located in the
vicinity (spark fl ight zone). Do not use dust extraction.
Due care should be taken that no sparks or sanding dust
fl ying from the workpiece come into contact with you.
When separating stone the guide shoe must be used!
The adjusting nut must be tightened before starting to work
with the machine.
The workpiece must be fi xed if it is not heavy enough to be
steady. Never lead the workpiece to the grinding disk with
your hand.
Under extreme conditions (e.g. smooth-grinding metals with
the arbour and vulcanized fi bre grinding wheel), signifi cant
contamination can build up on the inside of the angle
grinder. For safety reasons, in such conditions the inside
should be cleaned thoroughly of metal deposits and a motor
circuit-breaker must be connected in series. If the motor
circuit-breaker trips the machine must be sent for repair.
For accessories intended to be fi tted with threaded hole
wheel, ensure that the thread in the wheel is long enough to
accept the spindle length.
For cutting-off work, always use the closed wheel guard,
which is available as an accessory.
Always disconnect the plug from the socket before carrying
out any work on the machine.
Keep mains lead clear from working range of the machine.
Always lead the cable away behind you.
Use clamps or another practical way to secure and support
the workpiece to a stable platform. Holding the work by your
hand or against the body leaves it unstable and may lead to
loss of control.
In case of cup-wheels, cones or plugs with threaded holes,
always ensure, that the depth of the threaded hole is deeper
than the threaded spindle length. Check the dimensions
according to the instructions of the specifi c grinding
accessory.
SPECIFIED CONDITIONS OF USE
This angle grinder can be used for separating, grinding and
wire brushing many diff erent materials, e.g. metal or stone.
In case of doubt please read the instructions of the
accessories manufacturer.
Do not use this product in any other way as stated for
normal use.
STARTUP PROTECTION
A zero-voltage switch prevents the machine from restarting
after a power failure. On resuming work, switch the machine
off and then back on again.
STARTING CURRENT LIMITER + SMOOTH START
The starting current for the machine is several times greater
than rated current. The starting current limiter reduces the
starting current to such an extent that a fuse (16 A,
slow-blow) is not tripped.
Electronic smooth start for save use prevents jerky run-up of
the machine.
ELECTRONICS
The speed of rotation is adjusted electronically when the
load increases.
In case of a longer overload period the speed is decreased
electronically. The machine continues to run slowly to cool
down the motor coil. After switching off and on the machine
can be used at rated load.
28 ENGLISH
414 794 - Varilex-WSF1800_16_Sprachen.indd 28 414 794 - Varilex-WSF1800_16_Sprachen.indd 28
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product
described under "Technical Data" fulfi lls all the relevant
provisions of the directives 2011/65/EU (RoHS), 2014/30/
EU, 2006/42/EC and the following harmonized standards
have been used:
EN 60745-1:2009+A11:2010
EN 60745-2-3:2011+A2:2013+A11:2014+A12:2014+A13:2015
EN 55014-1:2017
EN 55014-2:2015
EN 61000-3-2:2014
EN 61000-3-3:2013
EN IEC 63000:2018
Geretsried, 2020-05-05
Gerd Eisenblätter
Authorized to compile the technical fi le

MAINS CONNECTION

Connect only to single-phase a.c. current and only to
the system voltage indicated on the rating plate. It is
also possible to connect to sockets without an earthing
contact as the design conforms to safety class II.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all
times.
Do not let any metal parts reach the airing slots - danger of
short circuit!
Use only Eisenblätter accessories and spare parts. Should
components need to be exchanged which have not been
described, please contact one of our Eisenblätter service
agents (see our list of guarantee/service addresses).
05.05.2020 09:16:31 05.05.2020 09:16:31