Publicidad
Idiomas disponibles
Idiomas disponibles
gb
3_USE
Insert the battery after ensuring that it has sufficient
charge by following the steps described in point 2 of this
manual.
Press the safety lock button (7) and then press the trigger
(6) to activate the tool.
To stop the tool, release the trigger (6).
Checking the automatic brake
Before making any cuts, idle the tool and release the
trigger (6) to stop the machine. The chain should stop 1
second after releasing the trigger, if this is not the case,
consult the technical service and do not use the tool.
WARNINGS
- Never use the tool with the saw guard attached.
- Never remove the guard (1) or handle it while working.
- Never activate the tool if the chain is in contact with or
resting on any material.
- Be careful when cutting branches, as the pressure
generated by the weight of the cut branch may cause you
to lose control of the tool.
- Be careful when cutting large shrubs and stems, as they
are flexible and could become entangled in the chain and
be thrown out.
Cutting
After activating the tool as described in the ON/OFF
section, allow the tool to reach its maximum speed before
starting to cut any material.
Support the tool on the cutting area using the support point
(4) under the chain and bar. Once the tool is supported,
proceed with the cut by applying light pressure in the
direction of the cut.
When making a cut, the tool will pull forward on the
material being cut. To avoid possible jamming, counteract
this force by pulling the tool slightly backwards as you
make the cut.
.
4_MAINTENANCE AND SERVICE
MAINTENANCE AND CLEANING
Before any work on the machine (e. g., maintenance,
tool change, etc.) as well as during transport and
storage, set the rotational direction switch to the
centre position.Unintentional actuation of the On/Off
switch can lead to injuries.
For safe and proper working, always keep the machine
and ventilation slots clean.
Cleaning
After finishing any work, clean the tool to prevent shavings
and sawdust from accumulating on the internal parts of
the tool, shortening its service life.
1- Remove the bar cover (1) following points 1 and 2 in
the section Changing the chain / bar (Figures A and B).
2- Clean the bar cover, the bar grooves (2) and the chain
sprocket with a soft brush. Remove any sawdust or wood
shavings.
3- Replace the cover and retighten the chain lever (5) and
secure it as indicated in the section Changing the chain /
bar in points 6, 7 and 8 (Figures F, G and H).
Changing the chain nut
If you notice that the chain nut is worn from use, it must
be replaced.
To replace the chain nut, the retaining washer must first
be removed. Both parts must be replaced at the same
time. After removing the old retaining washer and gear,
first install the new gear and then the new retaining
washer.
Battery
When the battery is no longer operative, please refer to
an authorised aftersales service agent for Stayer power
tools.
If the machine should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an aftersales service centre for Stayer
power tools.
TRANSPORT
he contained lithiumion batteries are subject to the
Dangerous Goods Legislation requirements. The user
can transport the batteries by road without further
requirements. When being transported by third parties
(e.g.: air transport or forwarding agency), special
requirements on packaging and labelling must be
observed. For preparation of the item being shipped,
consulting an expert for hazardous material is required.
Dispatch batteries only when the housing is undamaged.
Tape or mask off open contacts and pack up the battery
in such a manner that it cannot move around in the
packaging. Please also observe possibly more detailed
national regulations.
DISPOSAL
The machine, accessories and packaging should be
sorted for environmental-friendly recycling.
Only for EC countries:
Do not dispose of power tools into house-hold
waste!
According the European Guideline 2012/19/EU for
Waste Electrical and Electronic Equipment and its
implementation into national right, power tools that a
re no longer usa-ble must be collected separately and
disposed of in an environmentally correct manner.
Battery packs/batteries:
Li-Ion:
Please observe the instructions in section
"Transport". Do not dispose of battery packs/batteries
into household waste, fire or water. Battery packs/
batteries should be collected, recycled or disposed of in
an environmental-friendly manner.
Only for EC countries:
Defective or dead out battery packs/batteries must be
recycled according the guideline 2006/66/CE.
-
14
-
Publicidad
