Cleaning & Maintenance; Environmental Protection - Metabo STE 140 Manual Original

The best way to determine the ideal setting is
through a practical trial.
8.4 Switching on/off, continuous operation
Fig. A
Avoid inadvertent starts: always switch the
tool off when the plug is removed from the
mains socket or if there has been a power cut.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore always hold the machine with
both hands using the handle provided, stand
securely and concentrate.
STE 140, STE 140 Plus:
Switching on: Push the slide switch (8) forward
(continuous operation).
Switching off: Push the slide switch (8) back.
STEB 140, STEB 140 Plus:
Switching on: Press the trigger (13). Press the
trigger more to increase the speed (up to preset
maximum speed, see chapter 8.3).
Switching off: Release the trigger (13).
Continuous operation: For continuous operation,
the pressed trigger (13) can be locked using the
lock button (14). To stop the machine, press the
trigger (13) again.
8.5 LED light (depending on fittings)
Fig. A
For working on dimly lit areas. The LED light (3)
lights up when the machine is connected and in
motion. The LED light switches off after a few
seconds when the machine is not in motion.
If the LED light is flashing, see chapter 10.
8.6 Note on use
Plunging You can plunge the jigsaw blade into
workpieces made from thin, soft materials without
needing to drill a hole beforehand. Only use short
saw blades. Only at 0° angle setting.
Set the adjustment lever (6) to the "0" position
(pendulum motion is deactivated). Position the
jigsaw with the front edge of the footplate (9) on the
workpiece. Hold the operating jigsaw firmly and
guide slowly downwards. Once the saw blade has
penetrated the workpiece, the pendulum motion
can be activated.
9. Cleaning, Maintenance
Clean the machine regularly. This includes
vacuum cleaning the ventilation louvres on the
motor.
Clean the saw blade clamping fixture regularly and
thoroughly by blowing with compressed air.
If necessary, clean the openings behind the saw
blade support roller (16).
Apply a drop of oil to the saw blade support roller
(16) from time to time.
STE 140 Plus, STEB 140 Plus: If necessary, adjust
the clamping force of the clamp lever (20) (
All manuals and user guides at all-guides.com
Fig. F
Fig. E): Release the safety screw (22) and turn the
clamping force screw (23) (turning the screw anti-
clockwise increases the clamping force). Tighten
the safety screw (22).
10. Troubleshooting
Only for STE 140 Plus, STEB 140 Plus:
The LED (3) is flashing and the machine is
not running. The restart protection is active.
If the mains plug is inserted with the machine
switched on, or if the current supply is restored
following an interruption, the machine does not start
up. Switch the machine off and on again.
11. Accessories
Only use original Metabo accessories
Use only accessories which fulfil the requirements
and specifications listed in these operating
instructions.
Fit accessories securely. Secure the machine if it is
operated in a bracket. Loss of control can cause
personal injury.
A Attaching the circular-cutting and parallel
guide
For sawing circles (dia. 100 - 360 mm) and making
cuts parallel with edges (max. 210 mm).
Attach the circular-cutting guide (
- Slide the rod on the circular-cutting and parallel
guide sideways into the footplate (centre point (c)
faces downwards).
- Set the desired radius (d).
- Tighten the screws (b).
Attach parallel guide (
- Slide the rod on the circular-cutting and parallel
guide sideways into the footplate (centre point (c)
faces upwards).
- Set the dimension (e)
- Tighten the screws (b).
For a complete range of accessories, see
www.metabo.com or the catalogue.
12. Repairs
Repairs to electrical tools must be carried out
by qualified electricians ONLY!
If you have Metabo electrical tools that require
repairs, please contact your Metabo service centre.
For addresses see www.metabo.com.
You can download spare parts lists from
www.metabo.com.

13. Environmental Protection

Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Only for EU countries: Never dispose of
power tools in your household waste! In
accordance with European Directive 2002/
96/EC on used electronic and electric equipment
ENGLISH en
Fig. G.
Fig. G-I)
Fig. G-II)
11