Publicidad
Idiomas disponibles
Idiomas disponibles
the rear side. The bowl is detached now. (Fig.16 on page 6)
• Finally, take out the auger and remove the seal hat cover (A)
and bowl seal ring (B). Replace if worn or for every 12 months.
(Fig.17 on page 7)
d) Remove the bowl and the lid:
ATTENTION! All of the previously disassembled and removed
components must be thoroughly washed and sanitized. We
strongly recommend daily cleaning and sanitizing this machine
in order to maintain high degree of food quality.
• To carry out this procedure correctly, proceed as follows:
- Fill a container with detergent and hot water with a temper-
ature of 50 ~ 60°C;
- Wash the disassembled components thoroughly with the de-
tergent solution.
- Rinse with hot water.
- Dip the disassembly components into the solution and soaked
for about 30 minutes.
- Then, wash the components again with clean water.
- Place different components on a dry, clean surface and dry
all parts well.
- Assembly the machine as described in below part e).
- Before starting operating the machine again, carry out the
rinsing cycle with clean water. (See below part f).)
WARNING! Do not immerse the bowl lids with lighting bulb in
any type of liquid. Before cleaning, please make sure the light-
ing bulb are removed from the machine as described as below
(Fig.29 on page 8).
To clean the lighted bowl lid as below:
1. Using a clean, damp cloth to wipe clean the bottom part of
the bowl lid & the outer surface.
2. Using a sponge dipped in the washing solution, sanitize the
bottom part (24) of the bowl lid, take care not to touch the
hinge part (X) for about 10 minutes (Fig.18 on page 7).
3. Rinse twice or more, with a clean sponge soaked in warm
fresh water.
4. Dry it with a dry clean cloth.
5. Put back the bowl lid only after the bowl has been cleaned
and sanitised.
e) Reassembly the washed components
ATTENTION! All of the washed components must be carefully
re-assembled. Some components must be adequately lubricat-
ed by the supplied lubricants in order to ensure that they work
efficiently.
• Always check for the integrity of the seal (A), should it be
worn, replace it with a new one (supplied).
• Replace the auger seal hat cover (A) for at least every 12
months.
• Insert the auger seal hat cover (A) as below. (Fig.19 on page
7).
• Lubricate the inside area of the auger seal hat cover (A) as
shown in Fig.20 on page 7 with the lubricant (Supplied).
• Then, insert the bowl seal ring (B) and lubricate with the sup-
plied lubricant around it as below. (Fig.21 on page 7)
• Next, insert the auger with the white washer (D) and black
washer (E) for the shaft. Rotate the auger to engage it. (Fig.22
on page 7)
• After that, set back the bowl in place, slightly raise head of the
auger so that it align wth the position (E) of the bowl. (Fig.23
on page 7)
• Press the bowl slightely downward until it engages with the
correct position and there will be a "click" sound. (Fig.24 on
page 7)
Follow below instructions to re-assembly the tap (7):
• Using the supplied lubricant, lubricate the cap (Y) adequately
and re-assembly the components.
• Fit the pin (F) while keep the tap lever steady. (Fig.25 on page
8)
• Replace the tap seal ring (C) if worn or leakage.
f) Rinsing the machine
ATTENTION! Before starting up the machine after cleaning, you
must carry ou the rinsing cycle.
Procedures as below:
• Pour out the clean water into bowl;
• Let the machine to run for at least 5 minutes in the "agitation"
• Switch off the machine and empty the bowl by opening the
tap.
g) Cleaning the drip tray
ATTENTION! The drip tray should be emptied and cleaned every
time the red float installed in the grid rises into view. It should
be cleaned daily.
• Lift the tray with the grid on top of it and pull it out. (Fig.26
on page 8)
• Wash the tray and the grid separately with the lukewarm wa-
ter.
• Dry both parts well and place back the grid on top of the tray.
• Position the drainage hose in the opening provided.
• Fit back the tray in place and press down to secure it with
the machine.
h) Lighting lid
ATTENTION! During the cleaning process, take care not to
bend, break or damage the „contacts" (Fig.27 on page 8). Any
damage might cause a bad functioing of the lighting lid.
• Clean the lid contacts using a damp cloth and dry well. Always
switch OFF the machine.
• Do not immersed in water for cleaning.
i) Bulb replacement
• The bulb should be replaced only when the machine is
switched OFF and the power cord is unplugged.
• Next, remove the protection caps. Then, using a proper
screwdriver (not supplied) to loosen the screws in order to
remove the cover (Fig.28 on page 8).
• Remove the bulb (U) from the socket (T) (Fig.29 on page 8).
And replace it with a new bulb (not supplied).
j) Cleaning the condenser
• ATTENTION! The condenser can only be cleaned solely by a
specialized technician, who must organize all of the opera-
tional sequences and with suitable tool/equipment.
• The condenser should be cleaned regularly (at least once per
every 6 months) to keep good machine performance.
• To access the condenser, the safety guards need to be re-
moved.
• WARNING! Removing safety guards will expose some sharp
surfaces of the machine.
GB
15
Publicidad
