Tabla De Contenido; Table Of Contents; Product Specifications; Proposition 65 Warning - KNOVA KN SS-18VVS Instrucciones De Uso

TABLE OF CONTENTS

Table of contents .............................................................. 1
Product specifications ...................................................... 1
Proposition 65 warning ...................................................... 1
Safety guidelines definitions ............................................ 1
Power tool safety ............................................................. 1
Additional safety rules for scroll saws .............................. 2
Electrical requirements and safety ................................... 3
Glossary of terms ............................................................. 4
Tools needed for assembly ................................................ 5
Carton contents ............................................................... 5

PRODUCT SPECIFICATIONS

Model
KN SS-18VVS
Motor:
120 V, 60 Hz, 1.6 A
Speed control:
Electric
Blade length:
5 in.
Type:
Pin-end of Pain-end
WARNING
To avoid electrical hazards, fire hazards or damage to the tool, use proper circuit protection.
This tool is wired at the factory for 110-120 Volt operation. It must be connected to a 110-120 Volt / 15 Ampere
time delay fuse or circuit breaker. To avoid shock or fire, replace power cord immediately if it is worn, cut or damaged
in any way. Before using your tool, it is critical that you read and understand these safety rules. Failure to follow these
rules could result in serious injury to you or damage to the tool.

PROPOSITION 65 WARNING

WARNING
Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains
chemicals known to the state of California to cause cancer, birth defects or other reproductive harm. Some examples
of these chemicals are:
• Lead from lead-based paints,
• Crystalline silica from bricks and cement and other masonry products, and
• Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these
chemical: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are
specially designed to fiter out microscopic particles. Handling the power cord on this product may expose you to chemicals
known to the state of California to cause cancer and birth defects or other reproductive harm. Wash hands after
handling. For more information go to: www.P65Warnings.ca.gov

SAFETY GUIDELINES DEFINITIONS

WARNING ICONS
Your power tool and its Instruction Manual may contain "WARNING ICONS" (a picture symbol intended to alert you to, and/or
instruct you how to avoid, a potentially hazardous condition). Understanding and heeding these symbols will help you operate your
tool better a. safer. Shown below are some of the symbols you may see.
SAFETY ALERT:
Precautions that
involve your safety.
WEAR RESPIRATORY
AND HEARING
PROTECTION:
Always wear respiratory
and hearing protection.

POWER TOOL SAFETY

GENERAL SAFETY INSTRUCTIONS BEFORE USING THIS
POWER TOOL Safety is a combination of common sense,
staying alert and knowing how to use your power tool.
WARNING
• To avoid mistakes that could cause
serious injury, do not plug the tool in until you have
read and understood the following.
Depth of throat:
Blade speed:
Blade stroke:
Depth of 90° cut:
Depth of 45° cut, left:
PROHIBITION
READ AND UNDERSTAND
INSTRUCTION MANUAL:
To reduce the risk of injury, user
and all bystanders must read and
understand instruction manual
before using this product.
1
Know your scroll saw ......................................................... 6
Assembly and adjustments .............................................. 7
Operating the tool ........................................................... 11
Maintenance .................................................................... 13
Troubleshooting guide ..................................................... 14
Parts list .......................................................................... 15
Schematic ........................................................................ 16
Stand parts list ................................................................ 17
Stand schematic .............................................................. 17
Notes ............................................................................... 18
Depth of 15° cut, right:
18 in. (457 mm)
Table size:
500 - 1500 SPM
Table tilt:
3/4 in. (19 mm)
Sawdust blower:
2-1/4 in. (57 mm)
Work light:
1-1/4 in. (32 mm)
WEAR EYE PROTECTION:
Always wear safety goggles or
safety glasses with side shields.
• Read all instructions before operating product. Failure
to follow all instructions listed below may result in
electric shock, fire and/or serious injury.
1. READ and become familiar with the entire
Instruction Manual. LEARN the tool's application,
limitations and possible hazards.
2-1/4 in. (57 mm)
12-5/8 in. x 20 in.
45º left; 15º right
Yes
LED
SUPPORT AND
CLAMP WORK
KEEP HANDS AWAY FROM THE
MOVING PART AND CUTTING
SURFACE: Failure to keep your
hands away from the moving part
and cutting surface will result in
serious personal injury.