Publicidad
Idiomas disponibles
Idiomas disponibles
REPLACING LED AERATOR WITH NON-LIGHTED AERATOR
1.
Hold the end of the faucet spout
(1.1) and turn the LED aerator (1.2)
clockwise to remove it from the
faucet body (A).
OPERATING INSTRUCTIONS
The lever handles control the flow of hot and cold water to the faucet. Moving the handle forward opens the cartridge and causes water to flow from the spout.
Rotate the handle on the right side of the faucet forward for cold water. Rotate the handle on the left side of the faucet forward for hot water. The degree of handle
opening determines the volume of water flow. Returning the handle to the original position away from the spout on the faucet body stops the flow of water.
CARE AND CLEANING
Clean periodically with a soft cloth. Avoid abrasive cleaners, steel wool, and harsh chemicals as these will dull the finish and void your warranty.
TROUBLESHOOTING
If a faucet installation doesn't deliver water properly or leaks, finding the cause and fixing it can be easy.
PROBLEM
Faucet leaks underneath
handle.
Water does not completely
shut off.
Faucet leaks around aerator.
Faucet has an improper
water pattern.
Homewerks.com
1
1.1
1.2
POSSIBLE CAUSE
Bonnet has come loose or o-ring on
cartridge is dirty or twisted.
Rubber valve seat is dirty, stuck, or
broken.
The aerator is incorrectly fitted, dirty,
or small parts inside the aerator are
improperly installed.
The aerator is dirty or small parts inside
the aerator are improperly installed.
2.
Thread the non-lighted aerator (C)
onto the end of the spout (2.1)
on the faucet body (A). Hand
tighten, but do not overtighten.
A
SOLUTION
1. Move the handle to the OFF position. Unscrew the handle screw and
remove the handle.
2. Tighten the bonnet by turning it clockwise. Move the cartridge stem
to the ON position. The leak should stop draining out from around the
cartridge stem.
3. If the leak does not stop, shut off the water supply. Remove the bonnet
by turning it counterclockwise. Lift out the cartridge valve. Inspect the
larger o-ring on the cartridge bonnet and the smaller o-ring on the
cartridge stem. Remove any debris from the o-rings. If either o-ring is
twisted, straighten it. If either o-ring is damaged, replace the cartridge by
calling customer service.
4. Position the cartridge back into the faucet body. Make sure the ridges on
the two sides of the cartridge bonnet fit into the grooves on the two sides
of the faucet body. Tightly screw the bonnet onto the faucet body.
5. Reinstall the handle.
1. Shut off the water supply.
2. Remove the handle from the faucet body. Loosen the bonnet by turning
it counterclockwise. Lift out the cartridge assembly.
3. Inspect the rubber valve seat in the faucet body. If there is debris or
brass scrap on the surface of the seat, remove it. If the rubber seat is
stuck tightly in the water inlet hole, push it gently with a fingertip so it
moves up and down smoothly. The spring (smaller end up) must be
placed back underneath the valve seat. If the rubber valve seat is worn
out or broken, replace the cartridge by calling customer service.
4. Position the cartridge back into the faucet body. Make sure the ridges on
the two sides of the cartridge bonnet fit into the grooves on the two sides
of the faucet body. Tightly screw the bonnet onto the faucet body.
5. Reinstall the handle.
1. Remove the aerator cover from the spout by turning it clockwise and
remove the aerator and gasket. Inspect the black rubber gasket inside
the aerator. The rubber gasket should be flat.
2. Reinstall the gasket and aerator, then replace and tighten the aerator
cover on the spout.
1. Remove the aerator cover from the spout by turning it clockwise and
remove the aerator and gasket.
2. Gently flush the small parts inside the aerator to clear away any debris.
3. Reinstall the gasket and aerator, then replace and tighten the aerator
cover on the spout. Ensure all parts are straight and flat.
3
2
2.1
A
C
Publicidad
