Wall Mounting - DeWalt DCS438 Manual De Instrucciones

may be removed from the exterior of the charger using
a cloth or soft non‑metallic brush. Do not use water or
any cleaning solutions.

Wall Mounting

Some D WALT chargers are designed to be wall mountable
e
or to sit upright on a table or work surface. If wall mounting,
locate the charger within reach of an electrical outlet, and
away from a corner or other obstructions which may impede
air flow. Use the back of the charger as a template for the
location of the mounting screws on the wall. Mount the
charger securely using drywall screws (purchased separately)
at least 1" (25.4 mm) long, with a screw head diameter of
0.28–0.35" (7–9 mm), screwed into wood to an optimal
depth leaving approximately 7/32" (5.5 mm) of the screw
exposed. Align the slots on the back of the charger with the
exposed screws and fully engage them in the slots.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Wheels

WARNING: To minimize the risk of eye injury, always
use eye protection. Carbide is a hard but brittle
material. Foreign objects in the workpiece such as wire
or nails can cause tips to crack or break. Mount the
wheel securely in proper direction of rotation before
using, and always use a clean, sharp wheel.

WARNING: To reduce the risk of injury, only use wheels
that are no greater than 3" (76 mm) in diameter, have
an inner diameter of 3/8" (or 7/16" if using adapter
ring), and without cutting teeth. Thickness of wheel not
to exceed 0.09" (2.2 mm). Never force a wheel onto the
machine or alter the size of the arbor hole.
A dull wheel will cause slow inefficient cutting, overload the
motor, could cause excessive splintering, and could increase
the possibility of kickback. Please refer to the table below to
determine the correct wheel for your application.
Wheel type
Diamond*** Multi‑Material
Wheel (DW8530)
Bonded Abrasive Wheel
(DW8711)
Diamond*** Tile Wheel
(DW47350)
Installing Wheels (Fig. A, D, J)

WARNING: Burn Hazard. Sharp parts. ALWAYS wear
gloves when changing wheels. Wheels have sharp
edges or may get extremely hot during operation, and
may damage bare hands.
Application
Drywall, fiber cement, plastic, steel, non
ferrous materials
Steel, stainless steel, non‑ferrous materials
Ceramic Tile, Porcelain and Granite/Marble/
Stone

WARNING: To reduce the risk of injury, only use wheels
that are no greater than 3" (76 mm) in diameter, have
an inner diameter of 3/8" (or 7/16" if using adapter
ring), and without cutting teeth. Thickness of wheel not
to exceed 0.09" (2.2 mm). Never force a wheel onto the
machine or alter the size of the arbor hole.

WARNING: Since accessories, other than those offered
by D WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
1. Remove the battery.
2. Lay unit on a firm surface, with the spindle
facing upward.
3. Hold spindle lock button
from turning. Spindle threads are left hand.
4. Using supplied 6 mm wrench
screw , outer flange
19
is installed and inner flange
left hand.
5. Slip the inner flange over the spindle.
nOTE: When intsalling 7/16" wheels, place the 7/16"
adaptor 17 over the inner flange.
6. Slip wheel over spindle. Make sure wheel goes over pilot
diameter of inner flange.
nOTE: When installing diamond*** wheels, always
match direction of rotation of the wheel to the desired
direction of rotation of the tool. Diamond*** wheels
will not cut effectively unless the direction marked on
the wheel matches the direction of rotation. Check the
setting of the forward/reverse/lock off button
sure it matches the direction marked on the wheel.
7. Slip on outer flange with the flat side towards the
cut‑off wheel.
nOTE: The text "LOOSE TIGHTEN" will be visible when
installed correctly.
8. Start threading on spindle screw which will self align
outer flange. Make sure the wheel is fitted in the
correct orientation.
9. Engage spindle lock button and tighten spindle screw
with wrench. Do not over tighten spindle screw.
10. Turn wheel by hand to ensure it is properly centered. The
wheel should not hit the shoe, guard or spindle screw.
The spindle screw and flanges should be tight.
Adjusting the Guard Angle (Fig. E)

WARNING: Remove battery first. To reduce the risk of
injury when grinding, ALWAYS adjust the guard to
provide the best control and protection. ALWAYS wear
gloves to protect your hands when adjusting the guard.
You can adjust the angle of the guard.
1. Remove the battery.
2. Grasp the guard 12 firmly and rotate to desired angle.
The guard can rotate 30 degrees, forward or backward.
English
WALT recommended
e
15
6 to keep the spindle
, remove spindle
13
, used wheel if one
18 20
. Spindle threads are
16
5
to make
11