VONROC CH510AC Traducción Del Manual Original página 8

EN
3. Status display
A. Temperature / Timer setting
B. Temperature indicator
C. Control lock
D. WiFi
4. Operating mode indicators
A. Comfort mode
B. Eco mode
C. Anti-frost mode
5. Screw
6. Floor stand
7. Wall mounting screw
8. Wall plug
9. Wall mounting bracket
3. OPERATION
Check the device for damage before use
and only use in good working condition.
When using the heater for the first time, you
may notice a slight smell originating from the
heating element. This is quite normal and it should
disappear after using the heater for some time.
Placing the convector panel heater on the floor
(fig. D)
• Install the floor stands (6) on the underside of
the heater (1) using the supplied screws (5)
(fig. D)
• Place the heater upright on a firm and level
surface.
• Keep a minimum distance of 1m from
combustible materials (furniture, curtains, etc.).
Keep away from wet environments.
Warning! Make sure to place the heater in
a safe spot, so you cannot easily trip over
the machine and cable. Make sure to place
the heater where it cannot fall down.
Mounting the convector panel heater on the wall
(fig. E-1, E-2, E-3, F-1, F-2, F-3)
• Observe the hole patterns in fig. E-1, E-2, E-3.
Find the hole pattern that corresponds to your
heater.
• For CH510AC / CH510AC_GREY /
CH510AC_WHITE see fig. E-1
• For CH511AC / CH511AC_GREY /
CH511AC_WHITE see fig. E-2
• For CH512AC / CH512AC_GREY /
CH512AC_WHITE see fig. E-3
8
• Install two wall mounting brackets (9) on
the wall using the included screws (7) (fig.
F-1). Use the included wall plugs (8) when
installing onto a concrete/brick wall. Refer to
the aforementioned hole pattern to ensure the
correct spacing between the brackets.
• Install two wall mounting brackets (9) on the
underside of the heater (1) using the included
screws (5) (fig. F-2). The installed brackets will
act as a stand-off to ensure the heater will be
positioned at the correct distance from the wall.
• Mount the convector heater panel to the wall by
sliding it onto wall brackets (fig. F-3).
Starting the convector panel heater (fig. B)
• Plug in the cable to the mains power outlet.
• Press the On/Off button (2F) on the control
panel. The control panel will now be activated.
• Use the Mode button (2D) to cycle between
operating modes. The selected operating mode
is displayed by the indicators 4A, 4B or 4C on
the control panel. The available modes are:
4A Comfort mode
4B Eco mode
4C Anti-frost mode Heating off, unless
Adjusting the temperature (fig. B)
• By default, the ambient temperature is shown
on the display. Press the Down or Up button (2A
or 2B) once to display the target temperature.
The target temperature will flash.
• While the target temperature is flashing, it may
be adjusted between 5°C and 50°C by pressing
the Down or Up buttons (2A or 2B).
• The target temperature will keep flashing for
5 seconds after the last button press, then the
display will revert to the default state showing
the ambient temperature.
• Note that the target temperature can not be
adjusted while the heater is in Anti-frost mode.
The target temperature is fixed to 5°C in this
operating mode. The operating mode must
first be changed to Comfort mode or Eco mode
before the target temperature can be adjusted.
Control panel lock (fig. B)
The control panel may be locked to prevent
accidental or unauthorized adjustments to the
heater settings. To lock the control panel, press
and hold the Up button (2B) for 3 seconds.
Heating at full power
Heating at 50% power
ambient temperature
drops below 5°C
WWW.VONROC.COM