Dry Vacuuming; Blower Function - Kärcher WD 2 Plus Manual

Installing the hose, pipes, floor nozzle
1. Connect the suction hose.
Illustration F
2. Connect the suction hose to the handle.
Illustration G
Note
For convenient vacuuming in confined spaces, the han-
dle can be removed, and the accessories plugged di-
rectly onto the suction hose.
To release the handle, the grey areas on both sides of
the handle must be pressed, and the handle pulled from
the hose.
3. Install the floor nozzle.
 Install the insert in the floor nozzle.
 Connect the floor nozzle to the suction pipes.
Illustration H
Starting up the device
1. Plug the mains plug into the socket.
Illustration I
Devices without a socket
2. Set the trigger into the desired position.
Illustration J
 Position "1 ON": The suction / blower function is
activated.
 Position "0 OFF": The device is switched off.
Devices with a socket
3. Set the trigger into the desired position.
Illustration K
 Position "1 ON": The suction / blower function is
activated.
 Position : When the power tool is connected,
the suction is activated automatically.
 Position "0 OFF": The device is switched off.
Note
As long as the device is supplied with power, the device
socket can be used as a power source.
Operation
Note
Pay attention to the latest part numbers when purchas-
ing and installing filter bags and cartridge filters.
Information on accessories and spare parts can be
found at www.kaercher.com.

Dry vacuuming

ATTENTION
Vacuuming cold ashes
Device damage
Only vacuum cold ash with an ash pre-separator.
ATTENTION
Defective or wet foam filter / cartridge filter
Device damage
Before starting up, check the foam filter / cartridge filter
for damage, and replace it if necessary. Only vacuum
with a dry foam filter / cartridge filter.
Depending on the equipment variant, a foam filter or a
cartridge filter is included.
 For devices with a foam filter: Always use the filter
bag in addition to the foam filter when dry vacuum-
ing.
 For devices with a cartridge filter: Always use the fil-
ter bag in addition to the cartridge filter when vacu-
uming fine dust.
Note
Replace the filter bag in good time, as a filter bag that is
too full could be damaged. The fill degree of the filter
bag depends on the amount of dirt vacuumed. The filter
bag should be replaced more frequently when vacuum-
ing fine dust, sand, etc.
ATTENTION
Wet vacuuming with a filter bag
Device damage
Do not use a filter bag when vacuuming wet.
ATTENTION
Operation with full container
When the container is full, a float switch closes the suc-
tion opening and the device runs at a higher speed.
Switch off the device immediately and empty the con-
tainer.
Note
If the device falls over, the float can also close. To make
the device capable of vacuuming again, set up the de-
vice, switch it off, wait 5 seconds and then switch it on
again.
Working with power tools (only for devices
with a built-in socket)
CAUTION
Unintentional starting of the power tool
Injury or property damage
Make sure that the power tool is ready for operation as
soon as it is connected to the device socket.
1. Connect the suction hose.
Illustration F
2. If necessary, adjust the adapter to the connection di-
ameter of the power tool using a suitable tool.
3. Put the adapter on the handle of the suction hose.
4. Mount the suction hose with the adapter on the pow-
er tool.
Illustration L
5. Plug the mains plug of the power tool into the device
socket.
Illustration M
6. Set the trigger to
Illustration K
The suction is activated automatically.
Note
Note the maximum connected load (see information on
the device socket).
Note
As soon as the power tool is switched on, the suction
turbine starts up with a 0.5 second delay. If the power
tool is switched off, the suction turbine continues to run
for approx. 5 seconds in order to suck in the residual dirt
in the suction hose.
The blower function can be used to clean areas that are
difficult to reach or where vacuuming is not possible,
e.g. leaves in a gravel bed.
 Insert the suction hose into the blower connection.
The blower function is now activated.
Illustration N






English
Wet vacuuming
.

Blower function

11