Before Use - HIKOKI NR 3675DD Instrucciones De Manejo

How to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its battery. If
you continue to use the tool and exhaust the electric
current, the battery may be damaged and its life will
become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate, and
the battery life will be shortened. Leave the battery and
recharge it after it has cooled for a while.
CAUTION
○ If the battery is charged while it is heated because
it has been left for a long time in a location subject to
direct sunlight or because the battery has just been
used, the charge indicator lamp of the charger lights
for 0.3 seconds, does not light for 0.3 seconds (off for
0.3 seconds). In such a case, fi rst let the battery cool,
then start charging.
○ When the charge indicator lamp fl ickers (at 0.2-second
intervals), check for and take out any foreign objects in
the charger's battery connector. If there are no foreign
objects, it is probable that the battery or charger is
malfunctioning. Take it to your authorized Service
Center.
○ Since the built-in micro computer takes about
3 seconds to confi rm that the battery being charged with
UC18YSL3 is taken out, wait for a minimum of 3 seconds
before reinserting it to continue charging. If the battery
is reinserted within 3 seconds, the battery may not be
properly charged.

BEFORE USE

Action
Removing and inserting the battery
Charging
Charging a USB device from a
electrical outlet
Charging a USB device and battery
from a electrical outlet
How to recharge USB device
When charging of USB device is
completed
Remaining battery indicator
(Battery: BSL36A18)
Selecting accessories
1. How to operate operation panel
(1) Power switch ON (See Fig. 4)
Under the condition of "Power switch OFF", push and
hold on Power switch more than 1 second, then power
indicator lights in Green.
NOTE
Do not press the push lever and/or pull the trigger during
the process of turning the power switch ON.
Doing so will prevent the power switch from turning ON.
[Auto power off ]
When the power is turned on but the Nailer is not used
for 30 minutes, the Nailer is automatically turned off . To
turn on again, press the power switch.
WARNING
Never leave the Nailer with the power on. This could
result in an accident.
(2) Power switch OFF (See Fig. 4)
Under the condition of "Power switch ON", push and
hold on Power switch more than 1 second, then power
indicator goes off .
Under the condition of "Power switch ON", functions
below are active.
(3) Select Nailing operation mode
(Full sequential actuation / Contact actuation)
After power switch turn ON, always set in Full sequential
actuation mode as initial. (Nailing operation indicator
light in blue.) (See Fig. 5)
To change nailing operation mode, push Nailing
operation switch once. Every pushing, mode will change
between "Full sequential" and "Contact". (See Fig. 6)
Lighting (Blue):
Blinking (Blue):
(4) Check Remaining battery level
The information indicator shows Remaining battery level
by status of LED lamp as below.
Status of indicator
(5) Information indicator
In case of operation error, LED lamps show as below.
Status of indicator
Figure Page
2 3
2 LEDs (Red) blink
3 3
2 LED lights blink in an
interval.
23-a 7
• In case of too hot
condition, Blink in
0.5 second interval.
23-b 7
• In case of too cold
condition, Blink in
24 7
0.25 second interval.
After 10 seconds, LED
25 7
lights and Power switch
automatically turn off .
26 7
― 8
2 LEDs blink in Orange,
after about 10 seconds,
automatically turn off
Power switch.
17
FULL SEQUENTIAL ACTUATION MECHANISM,
CONTACT ACTUATION MECHANISM
The battery remaining
power is nearly empty.
Recharge the battery as
soon as possible.
1 LED (Red) blinks
Machine is in too cold
(below -5°C) or too hot
condition.
Allow the nailer to cool
or warm-up thoroughly in
adequate condition.
Contact HiKOKI for
inspection.
English