Publicidad
Idiomas disponibles
Idiomas disponibles
Charger Operation
Refer to the indicators below for the charge status of
the battery pack.
DCB107, DCB112, DCB113, DCB115, DCB118, DCB132
Charging
Fully Charged
Hot/Cold Pack Delay*
* DCB107, DCB112, DCB113, DCB115, DCB118,
DCB132: The red light will continue to blink, but a
yellow indicator light will be illuminated during this
operation. Once the battery pack has reached an
appropriate temperature, the yellow light will turn off
and the charger will resume the charging procedure.
The compatible charger(s) will not charge a faulty
battery pack. The charger will indicate faulty battery
pack by refusing to light.
NOTE: This could also mean a problem with a charger.
If the charger indicates a problem, take the charger and
battery pack to be tested at an authorized service center.
Hot/Cold Pack Delay
When the charger detects a battery pack that is too
hot or too cold, it automatically starts a Hot/Cold Pack
Delay, suspending charging until the battery pack has
reached an appropriate temperature. The charger then
automatically switches to the pack charging mode.
This feature ensures maximum battery pack life.
A cold battery pack will charge at a slower rate than
a warm battery pack. The battery pack will charge at
that slower rate throughout the entire charging cycle
and will not return to maximum charge rate even if the
battery pack warms.
The DCB118 charger is equipped with an internal fan
designed to cool the battery pack. The fan will turn
on automatically when the battery pack needs to be
cooled.
Never operate the charger if the fan does not operate
properly or if ventilation slots are blocked. Do not
permit foreign objects to enter the interior of the
charger.
Electronic Protection System
Li-Ion tools are designed with an Electronic Protection
System that will protect the battery pack against
overloading, overheating or deep discharge.
The tool will automatically turn off if the Electronic
Protection System engages. If this occurs, place the
lithium-ion battery pack on the charger until it is fully
charged.
Wall Mounting
DCB107, DCB112, DCB113, DCB115,
DCB118, DCB132
These chargers are designed to be wall mountable
or to sit upright on a table or work surface. If wall
mounting, locate the charger within reach of an
electrical outlet, and away from a corner or other
obstructions which may impede air flow. Use the
back of the charger as a template for the location of
the mounting screws on the wall. Mount the charger
securely using drywall screws (purchased separately)
at least 1" (25.4 mm) long, with a screw head diameter
of 0.28–0.35" (7–9 mm), screwed into wood to an
optimal depth leaving approximately 7/32" (5.5 mm)
of the screw exposed. Align the slots on the back of
the charger with the exposed screws and fully engage
them in the slots.
Charger Cleaning Instructions
WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger
using a cloth or soft non-metallic brush. Do not use
water or any cleaning solutions.
Important Charging Notes
1. Longest life and best performance can be
obtained if the battery pack is charged when the
air temperature is between 65 °F and 75 °F (18 °
– 24 °C). DO NOT charge the battery pack below
+40 °F (+4.5 °C), or above +104 °F (+40 °C). This
is important and will prevent serious damage to
the battery pack.
2. The charger and battery pack may become warm
to the touch while charging. This is a normal
condition, and does not indicate a problem. To
facilitate the cooling of the battery pack after use,
avoid placing the charger or battery pack in a
warm environment such as in a metal shed or an
uninsulated trailer.
3. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in
a lamp or other appliance.
b. Check to see if receptacle is connected to a
light switch which turns power off when you
turn out the lights.
c. Move the charger and battery pack to
a location where the surrounding air
temperature is approximately 65 °F – 75 °F
(18 ° – 24 °C).
d. If charging problems persist, take the tool,
battery pack and charger to your local service
center.
ENGLISH
9
Publicidad
