Publicidad
Idiomas disponibles
Idiomas disponibles
(contact with or inhala
of the dust may cause allergic rea
operator or bystanders); wear a dust mask and work with a dust extr
• Certain kinds of dust are classified as carcinogenic (such as oak and beech dust) especially in c
with a
ves for wood c
wear a dust mask and work with a dust extr
connectable
• Follow the dust-related na
requirements for the materials you want to work with
• Wear prot
ve gloves, safety glasses, close-fi
• Secure the workpiece (a workpiece clamped with clamping devices or in a vice is held more securely than
by hand)
• When sanding metal, sparks are generated; do not use dustbox and keep other persons and combus
material from work area
DURING USE
• Always keep the cord away from moving parts of the tool; direct the cord to the rear, away from the tool
• Do not touch the moving sanding disc
• In case of electrical or mechanic
• If the cord is damaged or cut through while working, do not touch the cord, but immediately disconnect
the plug
AFTER USE
• When you put away the tool, switch off the motor and ensure that all moving parts have come to a
complete stands
CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire in the cord of this tool to the earth terminal of
the plug
• If for any reason the old plug is cut off the cord of this tool, it must be disposed of safely and not le
una ended
SYMBOLS
Read the manual
Warning
Double isula
Wear eye prot
OPERATING INSTRUCTION
(Fig.3)
Before the first use
Remove the finishing sander and all accessories out of the packaging and check all parts for damage in
transit.Keep packaging material out of reach of children. There is risk of suffoca
Paper Choose the sanding paper according to the material being worked. Use sanding paper with a 40
resp, 60 grain for rough sanding and on uneven surfaces. Use the finder grain of 120 for smoother finish.
1. A ach the sanding paper on the sanding plate and make sure the holes on the sanding paper fit with
openings on the base plate. Only this way the sanding dust can be extracted thr
sanding plate.
2. Firmly press sanding paper down on the sanding plate.
Always use abrasive papers suited to the material you want to sand. Then papers must have correct grain
size.
4
s and/or respiratory diseases to the
evice when connectable
device when
rot
for long hair)
ately switch off the tool and disconnect the plug
Wear ear prot
Wear dusk mask
Do not dispose of old appliances in the
household garbage
Disconnect from power supply while
maintance
A aching Sanding
GB
Depending on grain size there are degrees of coarseness. The coarseness is specified by a number on the
back of papers. The higher the number is, the finer the grain.
It is important to use the right paper for each job. For rough sanding use grain sizes up to 80, f
as larch, pine or spruce use papers from 60grit to 150grit.For dense hardwood as beech or maple, the grain
sizes with up to 220 can be used.
Assembling/Disassembling/Emptying the Dust Bag
Always use the dust bag when sanding
1. Place the dust bag onto the provided exhaust c
2. To remove the dust c
ox, just pull the box outwards. Preferably clean the dust c
and the exhause c
a er each use. By doing this the dust c
easily inserted and removed.
3. For emptying the dust c
g, just tap out or, if available, clean with compressed air.
Switch off the machine, disconnect the power.
(Fig.2)
Switching on and off
1. Connect the plug to a power socket
2. Switch on con
ra
ress bu on(2)
3. Switch off con
ra
ress bu on(2)
Sanding
1. P
n re sanding surface on the piece of work
2. Switch the machine on and guide it over the surface to be sanded using cir
ressure to the machine when sanding, the weight of the machine itself is usually sufficient to
ensure op
rev
good r
paper that gradually gets finder.
CLEANING AND MAINTENANCE
CAUTION! Before performing any care or maintenance work, disconnect from the power.
Use a dry brush to clean the dust extr
not use solvents! Then dry well. Remove the dust c
carefully, try not to create dust. Do not breathe in saw dust! Wash out the bag in cold soapy water and
allow drying.
Before each use, check the machine, the cable and accessories to ensure that they are not damaged. Have
any necessary repairs completed by a specialist.
Machines that no long
roperly should be disposed off correctly in accordance with the local
regula
ENVIRONMENT
Do not dispose of electric tools, accessories and packaging together with household waste material -
in observance of European Dir
ve 2002/96/EC on waste of electric and electronic equipment and its
implementa
cordance with na
aw, electric tools that have reached the end of their life must
be collected separately and returned to an environmentally compa
TROUBLE SHOOTING
Fault Symptom
Possible Cause
(Fig.1)
ox up to the end into housing.
ox can be
ete several sanding processes using sand
rom the plas
to empty. Empty
recycling facility.
Tr
GB
wood
ox
5
Publicidad
Solución de problemas
