Publicidad
Idiomas disponibles
Idiomas disponibles
clockwise.
The mitre table features positive click stops at 0°, 15°, 22.5°,
30° and 45° for quick setting of common mitre angles.
3. BEVEL LOCK (SEE FIG. G1, G2)
The bevel lock (20) is used to set the blade at the desired
bevel angle. The mitre saw bevel cuts from 0° to 45° to the
left. To adjust the bevel angle, loosen the bevel lock and
adjust the saw arm to the desired bevel angle.
NOTE: Assembly the work clamp (15) on the right side
before adjusting into bevel cut mode.
4. SPINDLE LOCK BUTTON (SEE FIG. H)
The spindle lock button (18) prevents the blade in the saw
from rotating. Depress and hold the spindle lock button
while installing, changing, or removing the blade.
OPERATION
1. STARTING THE SAW (SEE FIG. I)
To turn on the saw, first push the lock-off lever as shown in
Fig. H, then squeeze the trigger switch (22).
To shut off, release the trigger switch.
2. CHOP CUT (SEE FIG. J)
1) Connect the machine to power outlet ensure that the
mains cable is clear of the blade and base plate.
2) Position the material to be cut on the rotating mitre table
(11), ensure it is firmly clamped so that it will not move
during cutting with the work clamp (15).
Ensure that the mitre table locking lever (8) and bevel
lock (20) are tightened before cutting.
WARNING: Failure to tighten the lock
screw can cause the blade to suddenly
climb up on the top of workpiece and force
itself toward you.
3) Before turning on the saw, perform a dry run of the
cutting operation just to make sure that no problems will
occur when the cut is made.
4) Hold the saw handle firmly, when squeezing the trigger
switch. Allow several seconds for the blade to reach
maximum speed.
5) Press the handle and slowly lower the blade into and
through the work-piece.
6) Release the trigger switch and allow the saw blade to
stop rotating BEFORE raising the blade out of the work-
piece. Wait until the electric brake stops the blade from
turning BEFORE removing the work-piece from the mitre
table.
3. BEVEL CUT (SEE FIG. K)
A bevel cut is a cut made across the grain of the work-piece
with the blade at an angle to the work-piece.
20
A straight bevel cut is made with the mitre table set in the 0
position and the blade set at an angle between 0
The saw can be moved from the normal 0° perpendicular
position to an angled position down to 45° from the
horizontal, on the left only.
Loosen the bevel lock (20) and tilt the saw head to the
left, until the desired angle is reached on the bevel scale.
Re-tighten the bevel lock and then follow the procedures of
chop cut.
4. MITRE CUT (SEE FIG. L)
A miter cut is made at 0° bevel and any miter angle in the
range from 45° left to 45° right.
Set the mitre angle follow the steps in MITRE TABLE LOCKS
section, and then follow the procedures of chop cut.
5. COMPOUND CUT (SEE FIG. M)
A compound mitre cut is a cut made using a mitre angle and
a bevel angle at the same time. This type of cut is used for
moldings, picture frames, and boxes with sloping sides.
Set the mitre and bevel angle following the steps in MITRE
TABLE LOCKS and BEVEL LOCK section, and then follow the
procedures of chop cut.
6. LED LIGHT (SEE FIG. N)
The mitre saw is equipped with a LED light which increases
visibility-great for dark or enclosed area.
To turn on the light, press the LED light on/off switch by
the position "
". To turn off, press the switch by the
position OFF.
MAINTENANCE
WARNING: Remove the plug from
the socket before carrying out any
adjustment, servicing or maintenance.
When all the adjustments, settings or
maintenance have been done, make sure that
all keys and wrenches have been removed
and that all screws, bolts and other fittings
are securely tightened.
There are no user serviceable parts in your power tool.
Never use water or chemical cleaners to clean your power
tool. Wipe clean with a dry cloth. Always store your power
tool in a dry place. Keep the motor ventilation slots clean.
Keep all working controls free of dust. Occasionally you may
see sparks through the ventilation slots. This is normal and
will not damage your power tool.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard.
o
and 45
.
o
o
EN
Publicidad
