Publicidad
Idiomas disponibles
Idiomas disponibles
B. Escape Posterior Exterior (Ducto Horizontal)
DESCRIPCIÓN GENERAL DE LA INSTALACIÓN
B1. Preparación de la pared trasera
B2. Desinstalación del placa del ventilador
B3. Montaje de la placa de instalación en la pared
B4. Preparación del gabinete superior
B5. Ajuste del ventilador
B6. Instalación del horno microondas
B1. PREPARAR LA PARED TRASERA PARA EL
ESCAPE TRASERO EXTERIOR
Es necesario realizar un corte en la pared trasera para crear una
abertura para la salida de extracción externa.
NOT E:
IT IS VER
REA D
AND FOLL
Y IMPO
IN THE
RTAN
INST ALLA
OW THE
T TO
BEFO
RE PRO
TION INST
DIRE CTIO
REA R
CEE DING
RUC TION
NS
WAL L
WITH
This Rear
TEM PLAT
THIS
S
Wall Templ
E.
3/8" TO EDGE
mounti
ng plate
ate serves
outlet.
and to
locate the
to positio
12"
1. Use
horizon
n the bottom
accura
a level
to check
tal exhaus
2. Locate
tely.
that the
templa
t
and mark
te is positio
right side
at least
ned
of the center
one stud
on the
4"
screw mount
It is import
line.
left or
of the microw
ed firmly
ant to use
at least
in a stud
one wood
locatio ns
for the
ave. Mark
two additio
to suppor
t the weight
3. Drill
holes in
supplie
nal, evenly
a stud,
the marke
d toggle
bolts.
spaced
Trim the
that do
drill a 3/16"
d locatio
rear wall
not line
hole for
wood screws
ns. Where
there is
toggle
bolts.
up with
a stud,
drill 5/8"
. For holes
AT THIS
DO NOT
INSTA LL
holes for
4. Remov
TIME.
THE MOUN
e the templa
TING PLATE
5. Review
the Installa
te from
installa
tion Instruc
the rear
wall.
tion situatio
n.
tion book
for your
Darle vuelta
versió n
a la hoja
en Espa
para consu
ol.
ltar la
Loca te
and mark
moun ting
holes to
plate .
align with
IMPO RTAN
T:
holes in
the
LOC ATE
AT LEAS
THE CEN
T ONE
TERL INE.
STUD
MAR K
THE LOC
ON EITH
SPAC
ER SIDE
ED TOG
ATIO N
FOR 2
OF
ARE A.
GLE BOLT
ADD ITION
S IN THE
AL, EVEN
MOU NTIN
LY
G PLAT
E
Trim the
rear wall
temp late
alon g
the dotte
d line.
Loca te
and mark
moun ting
holes to
IMPO RTAN
plate .
align with
LOC ATE
T:
AT LEAS
THE CEN
T ONE
TERL INE.
STUD
MAR K
ON EITH
THE LOC
SPAC
ED TOG
ATIO N
GLE BOLT
FOR 2
ADD ITION
ARE A.
S IN THE
□ Lea las instrucciones de la sección PLANTILLA PARA LA PARED
TRASERA.
3/8" TO EDGE
12"
NOTE: IT IS VERY IMPORTANT
TO
READ AND FOLLOW
THE DIRECTIONS
INSTRUCTIO NS
IN THE INSTALLATI ON
BEFORE PROCEEDIN
G WITH THIS
REAR WALL TEMPLATE.
4"
serves to position the bottom
This Rear Wall Template
the horizontal exhaust
mounting plate and to locate
outlet.
the template is positioned
1. Use a level to check that
accurately.
one stud on the left or
2. Locate and mark at least
right side of the centerline.
It is important to use at
least one wood
a stud to support the weight
screw mounted firmly in
two additional, evenly spaced
of the microwave. Mark
locations for the supplied
toggle bolts.
locations. Where there
is
3. Drill holes in the marked
for wood screws. For holes
a stud, drill a 3/16" hole
a stud, drill 5/8" holes for
that do not line up with
toggle bolts.
MOUNTING PLATE
DO NOT INSTALL THE
AT THIS TIME.
from the rear wall.
4. Remove the template
e Installation Instruction
book for your
5. Revie
w
h t
installation situation.
para consultar la
Darle vuelta a la hoja
versión en Español.
to align with holes in the
Locate and mark holes
mounting plate.
IMPORTANT :
STUD ON EITHER SIDE
OF
LOCATE AT LEAST ONE
THE CENTERLIN E.
FOR 2 ADDITIONAL ,
EVENLY
MARK THE LOCATION
IN THE MOUNTING PLATE
SPACED TOGGLE BOLTS
AREA.
Locate and mark holes
m
o
u
t n
n i
g
l p
IMPORTANT :
LOCATE AT LEAST ONE
THE CENTERLIN E.
MARK THE LOCATION
along the dotted line.
Trim the rear wall template
SPACED TOGGLE BOLTS
AREA.
temp late
alon g
the dotte
d line.
holes in
the
ER SIDE
OF
AL, EVEN
MOU NTIN
LY
G PLAT
E
along the dotted line.
Trim the rear wall template
to align with holes in the
t a
. e
OF
STUD ON EITHER SIDE
FOR 2 ADDITIONAL ,
EVENLY
IN THE MOUNTING PLATE
□ Adhiera con cinta la plantilla a la pared trasera, alineándola con
los agujeros previamente taladrados pares coincidir con los
agujeros A y B en la placa para la pared.
□ Realice el corte de la abertura, siguiendo las instrucciones de la
sección PLANTILLA PARA LA PARED TRASERA.
B2. QUITAR LA PLACA DEL SOPLADOR
Quite y guarde el tornillo que sujeta la placa del ventilador al
microondas. Levante la placa del ventilador para retirarla.
Placa del ventilador
18
Asegúrese de que los tornillos del motor del
NOTA :
ventilador y laplaca del ventilador queden firmemente
apretados al volver a instalarlos. Esto ayudará a
prevenir el exceso de vibraciones.
NOTA :
Asegúrese de que el cableado del motor quede
debidamente orientado y asegurado, y que los cables
no queden atrapados.
Parte trasera
del microondas
Publicidad
