Explanation Display functions
Time
- Without setting the target value, time will count up�
- When setting the target value, time will count down from your
target time to 0 and alarm will sound or flash�
- Range 0:00~99:59
Speed
- Displays current training speed�
Maximum speed is 99.9 KM/H or ML/H.
- Without any signal being transmitted into the monitor for 4
seconds during workout, SPEED will display "0�0"
RPM
- Displays the Rotation Per Minute�
Display range 0~15~999
- Without any signal being transmitted into the monitor for 4
seconds during workout, RPM will display "0"
Watt
- Display current workout watts�
- Range 0 ~ 999
•
Symbol is displayed in Watt window when set target Watt is
lower than current workout watt output�
You pedal too fast, or set target is too low�
•
Symbol is displayed in Watt window when set target Watt is
higher than current workout watt output�
You pedal too slow, or set target is too high�
Level
- Shows tension level setting, when adjusting resistance, for 3
seconds�
Distance
- Without setting the target value, distance will count up�
- When setting the target value, distance will count down from your
target distance to 0 with an alarm sound or flash�
- Range 0.00~99.99
Calories
- Without setting the target value, calorie will count up�
- When setting the target value, calories will count down from your
target calorie to 0 with an alarm sound or flash�
- Range 0~999.
‼ NOTE
• This data is a rough guide for comparison of different exercise
sessions which cannot be used in medical treatment
Pulse
- Current pulse will display after 6 seconds when detected by the
console�
- Without any pulse signal for 6 seconds, console will display "P"�
- Pulse alarm will sound when current pulse is over the target pulse�
- Range 0-30~230 BPM
BAI ™
- Display BAI consumption BAI value during workout�
- Display range 0~999
‼ NOTE
• BAI (Body Activity Index) is the sum up of effective training
volume�
• Training volume = Training Intensity x Training time.
BAI calculates effective training volume based on your heart rate,
age, gender and duration�
During the workout, you can see BAI accumulates� As soon as you
complete a workout session, you can obtain a total BAI point of this
session, which is the total effective training volume of this session�
If you train harder, higher heart rate zone, you get BAI points faster� If
you train less hard, lower heart rate zone, you get BAI points slow�
We recommend to workout by accumulating 100 BAI points every
week to enhance your cardio capability�
Centre display
- Top digits shows workout parameters in larger font� When display is
in Scan mode, each parameter will be displayed for a few seconds�
Displayed value name will blink in dedicated window�
- Lower Dot display will show the program profile intensity curve
graphically�
* In tension control: Each dot represents 2 tension levels�
* In HRC mode: Each dot represents a tension level as if it was
tension controlled�
* In Watt mode: Each dot represents a tension level as if it was
tension controlled�
Explanation of buttons
Up (Dail)
- Increase resistance level
- Setting selection�
Down (Dail)
- Decrease resistance level
- Setting selection�
Mode/ Enter
- Confirm setting or selection�
- Stop display scan function, and fix current parameter in centre
display�
- Go to next parameter when being in Fixed display mode�
‼ NOTE
• When stopped the scan mode by fixing a specific parameter,
there is no way to activate the "scan" function again, other than
quickly press "Start/ Stop" twice to rapidly pause and restart
your workout again�
Reset
- In setting mode, press RESET key once to reset the current function
figures�
- Press RESET key and hold for 3 seconds to reset all function figures
Start/ Stop
- Start or Stop workout
Body Fat
- Test body fat% and BMI in stop mode�
Recovery
- After the console detects pulse signal, press the RECOVERY key to
enter recovery mode to monitor heart rate recovery ability
2 9
English