ST MP2 500-R Li D48 Serie Manual De Instrucciones página 121

6.4.1 Grass cutting
1. Start moving forward and mowing in the grass area.
2. Regulate the forward speed and the cutting height
(par. 5.6) considering the conditions of the lawn (the
height, density and dampness of the grass) and the
amount of grass collected;
3. The appearance of the lawn will improve if you alternate
cutting in both directions at the same height (Fig.16.A).
4. Never cut more than one third of the total grass height
per single pass (Fig.16.B).
5. It is recommended to avoid mowing on slopes with an
angle steeper than 15 degrees.
6.4.2 Emptying the grass catcher
When the grass catcher (Fig.1.E) is too full, grass collection is
no longer efficient and the sound of the lawnmower changes.
To remove and empty the grass catcher:
1. Release both levers (Fig.17.A) and (Fig.17.B).
2. Wait until the cutting means stops.
3. Grasp the handle and remove the grass catcher keeping
it in an erect position.
6.5 STOP
To stop the machine:
1. Release both levers (Fig.17.A) and (Fig.17.B).
2. Press the power button (Fig.14.A).
3. Wait until the cutting means stops.
When you have stopped the machine, it will take a
few seconds for the cutting means to stop.
IMPORTANT Always stop the machine.
• When moving between work areas.
• When driving on grass free surfaces.
• Every time it is necessary to overcome an obstacle.
• Before adjusting the cutting height.
• Whenever you remove or reattach the grass catcher.
• Whenever you remove or reattach the
side discharge chute (if provided).
6.6 AFTER OPERATION
1. Stop the machine (par. 6.5).
2. Open the hatch and remove the safety key.
3. Remove the batteries from their housing and recharge
them (par 7.2.2).
4. Allow the motor to cool before storing in an enclosed
space.
5. Clean (par. 7.3).
6. Check there are no loose or damaged components. If
necessary, replace the damaged components and tight-
en any screws and loose bolts or contact the authorised
service centre.
IMPORTANT Remove the safety key whenever
the machine is unused or left unattended.
7. ROUTINE MAINTENANCE
7.1 GENERAL INFORMATION
The safety regulations to follow are described in
chap. 2. Strictly comply with these indications to avoid
serious risks or dangers.
Before conducting any inspections, cleaning or
maintenance/adjustment interventions on the machine:
• Stop the machine.
• Remove the safety key, (never leave the key in the ignition
or within reach of children or unauthorised persons).
• Make sure that all moving parts have come to a complete
stop.
• Allow the motor to cool before storing in an enclosed space.
• Read the relevant instructions.
• Use suitable clothing, protective gloves and goggles.
– The frequency and types of maintenance are
summarised in the "Maintenance Table". The table
will help you maintain your machine's safety and
performance. It summarises the main interventions to
be made and the frequency applicable to each of them.
Carry out the relevant intervention according to the first
deadline.
– The use of non-genuine and/or incorrectly assembled
spare parts and attachments could adversely affect
machine operation and safety. The manufacturer shall
decline all liability in the event of injuries or damages
caused by such parts.
– Genuine spare parts are supplied by authorised
assistance workshops and dealers.
IMPORTANT Any maintenance and adjustment operations
not described in this manual must be carried out by your
Authorised Service Centre.
7.2 BATTERY
7.2.1 Battery power reserve
Battery power reserve (and therefore the movable lawn
surface before recharging is required) mainly depends on:
a. environmental
requirements:
– mowing dense, high and/or wet grass;
b. machine cutting width; the wider the width, the greater is
the energy need;
c. operator behaviour that should be avoided:
– switching the machine on and off frequently whilst
working;
– setting a cutting height that is too low for the lawn
conditions;
– working at a speed that is too high in relation to the
amount of grass to be removed.
NOTE During use, the battery is protected against total
drainage with a protective device that switches off the
machine and stops it from working.
EN - 8
factors, that cause higher energy