Publicidad
Idiomas disponibles
Idiomas disponibles
OBJ_BUCH-0000000506-001.book Page 36 Thursday, January 12, 2023 12:14 PM
en
36
Observe the dimensions of the grinding tools.
Ensure that both X-LOCK latch noses are open
before mounting the X-LOCK application tool. If nec-
essary, clean the area between the two X-LOCK latch
noses.
After mounting, check that the edge of the grind-
ing accessory is not higher than the reference sur-
face and thus correctly mounted. If the edge is higher,
the mount must be cleaned or the grinding accessory
may not be used.
Press the lever (see page 9) only when the motor
is stopped.
Do not switch the power tool on with the clamp-
ing lever open. Otherwise there is a risk of crush-
ing the hand and fingers.
Do not reach into the area of the clamping jaws.
Otherwise there is a risk of crushing the fingers.
Turning the machine head:
Carefully turn the machine head to the new position
(see page 15) without removing it from the housing.
Features
The soft start is used to reduce torque reaction forces
when switching on and running up the power tool to
the no-load speed.
The restarting protection prevents the power tool from
automatically restarting if the power supply is inter-
rupted during operation. In this case, switch off the
power tool, check the power supply and then switch
the power tool on again.
The electronic overload protection reduces the risk of
motor damage if the power tool is overloaded. In this
case, the power tool switches off automatically. After-
wards, set the switch to the off position, remove the
power tool from the workpiece and check the applica-
tion tool for damage. Then, switch the power tool on
again.
Charge-control Indicator on the Battery
(see page 13).
The charge condition can be indicated by the green
LEDs of the charge-control indicator on the battery.
Press the charge-control indicator button
to indicate the charge condition.
When no LED lights up after pressing the charge-con-
trol indicator button, the battery is defective and must
be replaced.
Transport.
The recommended Li-ion batteries are subject to the
Dangerous Goods Legislation requirements. The user
can transport the batteries by road without further
requirements.
When being transported by third parties (e.g.: air trans-
port or forwarding agency), special requirements on
packaging and labelling must be observed. For prepara-
tion of the item being shipped, consulting an expert for
hazardous material is required.
Dispatch batteries only when the housing is undam-
aged. Tape or mask off open contacts and pack up the
battery in such a manner that it cannot move around in
the packaging. Please also observe possibly more
detailed national regulations.
Repair and customer service.
Please observe that power tools may only be
repaired, maintained and inspected by qualified
electricians, as improper maintenance can result in con-
siderable hazards for the user.
When working metal under extreme oper-
ating conditions, it is possible for conductive
dust to settle in the interior of the power
tool. Blow out the interior of the power tool via the
ventilation slots frequently with dry and oil-free com-
pressed air.
When working materials containing gypsum, dust may
occur. This dust can settle inside the power tool as well
as on switching elements and harden in combination
with humidity. As a result, the switching mechanism
may be impaired.
Blow out the interior of the power tool frequently
through the ventilation openings and switching ele-
ments using dry, oil-free compressed air.
Products that have come into contact with asbestos
may not be sent in for repair. Dispose of products con-
taminated with asbestos according to the applicable
country-specific regulations for such disposal.
For FEIN power tools and accessories in need of repair,
please contact your FEIN after-sales service. The
address can be found on the Internet under
www.fein.com.
Renew stickers and warning indications on the power
tool when aged and worn.
The current spares parts list for this power tool can be
found on our website at www.fein.com.
Use only original spare parts.
If required, you can change the following parts your-
self:
Application tools, clamping flanges (where applicable),
wheel guard, battery, auxiliary handle, dust-protection
filter, hand protection
Maintenance and cleaning.
Occasionally clean the ventilation slots and the battery
terminals with a soft, clean and dry brush.
– Do not use chemical substances for cleaning the bat-
or
tery.
Warranty and liability.
The warranty for the product is valid in accordance
with the legal regulations in the country where it is mar-
keted. In addition, FEIN also provides a guarantee in
accordance with the FEIN manufacturer's warranty dec-
laration.
The delivery scope of your power tool may include
only a part of the accessories described or shown in this
Instruction Manual.
Declaration of conformity.
This CE declaration is only valid for European Union
and EFTA (European Free Trade Association) countries
and only for products intended for the EU- or EFTA
market. After placing the product on the EU market the
UKCA mark loses its mark validity.
Publicidad
