Publicidad
Idiomas disponibles
Idiomas disponibles
Diode on red – charging is in progress (once the battery is connected
to the charger).
Diode on green again – the battery is fully charged.
Once the battery has been charged, the LED diode (11) is lit green until
you disconnect the charger from mains network.
Batteries heat up strongly when charging. Do not operate just
after charging – wait for the battery to cool down to room
temperature. It will prevent battery damage.
SPINDLE BRAKE
Drill is equipped with electronic brake that stops the spindle immediately
after the switch button (6) is released. The brake ensures precision when
screwing or drilling and prevents free spindle rotation after switching off.
OPERATION / SETTINGS
SWITCHING ON / SWITCHING OFF
Switching on – press the switch button (6).
Switching off – release the switch button (6).
Each time the switch button (6) is pressed, the LED diode (7) lights up to
illuminate the workplace.
ROTATIONAL SPEED CONTROL
Increase or reduce pressure on the switch button (6) to adjust drilling or
driving speed while operating. Speed adjustment allows for a soft start,
which prevents dill slipping when drilling holes in gypsum or glaze, and
allows for operation control when screwing in and out.
OVERLOAD CLUTCH
Set the torque adjustment ring (2) in appropriate position to permanently
set overload clutch to defined torque value. When the set torque is
reached, overload clutch disconnects automatically. It prevents screwing
screws too deep or damaging the drill.
TORQUE ADJUSTMENT
Different screws and materials require different torque to be applied.
The bigger the number corresponding to given position, the bigger is
the torque (fig. C).
Set the torque adjustment ring (2) to appropriate torque value.
Always start operation with low torque.
Increase the torque gradually until obtaining desired results.
Use higher settings to unscrew screws.
When drilling, choose setting marked with the drill symbol. The torque is
the greatest with this setting.
Knowledge how to choose appropriate torque setting comes with
practice
Setting the torque adjustment ring in the drilling position
deactivates the overload clutch.
WORKING TOOL INSTALLATION
Set the direction selector switch (3) in the middle position.
Hold the rear ring of the quick release chuck (1) and turn the front ring
counter clockwise. Turn until jaws spread properly and allow to insert drill
or driver bit (fig. D).
Hold the rear ring of the quick release chuck (1), turn front ring
clockwise and tighten firmly to install work tool.
Deinstallation of tool is similar to installation, only the sequence of actions
is reversed.
Make sure the tool position is correct when installing drill or
driver bit in the quick release chuck. Use additional magnetic
adapter as an extension when using short driver bits.
LEFT – RIGHT DIRECTION OF ROTATION
Choose direction of spindle rotation with the direction selector switch (3)
(fig. E).
Clockwise rotation – set the direction selector switch (3) to the
extreme left position.
Counter-clockwise rotation – set the direction selector switch
(3) to the extreme right position.
* In certain cases position of the switch related to rotation may be different
than specified. Please refer to graphic signs placed on the switch or tool
body.
Safe position of the direction selector switch (3) is in the middle, it prevents
accidental starting of the power tool.
Drill cannot be started, when the switch is in this position.
Use this position of the switch to change drills or bits.
Before starting the tool make sure the position of the direction selector
switch (3) is correct.
Do not change direction of rotation when the drill spindle is
rotating.
CHANGE OF GEAR
Gear switch (8) (fig. H) allows to increase the range of rotational speed.
Gear I: small speed range, big torque
Gear II: greater speed range, small torque.
Set the gear switch in position appropriate for the works to perform. When
the switch is blocked and cannot be moved, turn the spindle slightly.
Never change the gear switch position when the drill is
operating. It may damage the power tool.
Long lasting drilling at low rotational speed of the spindle may
cause motor overheating. Provide regular breaks during
operation or let the tool operate at maximum speed with no
load for approximately 2–3 minutes.
OPERATION AND MAINTENANCE
MAINTENANCE AND STORAGE
Cleaning the device after each use is recommended.
Do not use water or any other liquid for cleaning.
Clean the drill with a dry cloth or blow with compressed air at low
pressure.
Do not use any cleaning agents or solvents, they may damage plastic
parts.
Clean ventilation holes in the motor casing regularly to prevent device
overheating.
In case of excessive commutator sparking, have the technical condition
of carbon brushes of the motor checked by a qualified person.
Store the drill in a dry place, beyond reach of children.
QUICK RELEASE CHUCK REPLACEMENT
Quick-release chuck is screwed onto spindle of the drill and additionally
secured with a screw.
Set the direction selector switch (3) in the middle position.
Open jaws of quick release chuck (1) and unscrew the fixing screw (left-
hand thread) (fig. F).
Install hexagonal key in the quick release chuck and tap the other end
of the key.
Unscrew the quick release chuck.
Installation of the quick release chuck is similar to deinstallation, only
the sequence of actions is reversed.
All defects should be repaired by service workshop authorized by the
manufacturer.
TECHNICAL PARAMETERS
RATED PARAMETERS
50G290 cordless drill / driver
Parametr
Battery voltage
Idle engine speed range
Quick-action grip range
Torque adjustment range
Max.
torque
(soft
applications)
Max.
torque
(hard
applications)
Drilling diameter in wood
Drilling diameter in metal
Drilling diameter in concrete
Spindle thread
Protection class
Mass
Year of production
50G290 stands for both the type and designation of the machine
Charger K113445
Parametr
Supply voltage
Power frequency
Maximum power
Charging voltage
Charging current
Ambient temperature range
Time of failure K113444
Protection class
Mass
Year of production
Parametr
Battery voltage
Battery type
7
20 V DC
gear I
0-400 min
gear II
0-1500 min
0,8 - 10 mm
1 – 20 + drilling
screwdriving
screwdriving
30 mm
10 mm
3/8" x 24UNF
230 V AC
21 V DC
2300 mA
0
5
C – 30
60 min
0,300 kg
Battery K113444
20 V DC
Li-Ion
Value
-1
-1
28 Nm
44 Nm
-
III
0,9 kg
2021
Value
50 Hz
65 W
0
C
II
2021
Value
Publicidad
