Publicidad
Idiomas disponibles
Idiomas disponibles
Fuel Gauge Battery Packs (Fig. C)
Some FACOM battery packs include a fuel gauge which consists
of three green LED lights that indicate the level of charge
remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
11
button
. A combination of the three green LED lights will
illuminate designating the level of charge left. When the level of
charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Proper Hand Position (Fig. E)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main handle
Variable Speed Trigger Switch (Fig. A)
To turn the tool on, squeeze the trigger switch
the tool off, release the trigger switch. Your tool is equipped
with a brake. The chuck will stop when the trigger switch is
fully released.
The variable speed switch enables you to start the application at
a slow speed. The further you squeeze the trigger, the faster the
tool will operate. For maximum tool life, use variable speed only
for starting holes or fasteners.
nOTE: Continuous use in variable speed range is not
recommended. It may damage the switch and should
be avoided.
Forward/Reverse Control Button (Fig. A)
A forward/reverse control button
the tool and also serves as a lock-off button.
To select forward rotation, release the trigger switch and depress
the forward/reverse control button on the right side of the tool.
To select reverse, depress the forward/reverse control button on
the left side of the tool. The centre position of the control button
locks the tool in the off position. When changing the position of
the control button, be sure the trigger is released.
1
. To turn
2
determines the direction of
nOTE: The first time the tool is run after changing the direction
of rotation, you may hear a click on start up. This is normal and
does not indicate a problem.
Worklight (Fig. A)
There is a worklight
worklight is activated when the trigger switch is depressed, and
will automatically turn off 20 seconds after the trigger switch is
released. If the trigger switch remains depressed, the worklight
will remain on.
nOTE: The worklight is for lighting the immediate work surface
and is not intended to be used as a flashlight.
Mode Selector (Fig. A, F)
Your tool is equipped with a mode selector
you to select one of two speeds or the Precision Control mode.
Select the speed/mode based on the application and control
the speed of the tool using the variable speed trigger switch
Precision Control™ (Fig. F)
In addition to normal impacting modes, this tool features the
Precision Control mode which grants the user greater control in
both fastening and loosening applications. To enable Precision
Control mode, place the mode selector on the foot of the tool
in the middle position. When in Precision Control mode and
operating in forward, the tool will fasten at 1900 RPM until
impact begins. The tool will then pause for 0.75 seconds before
continuing to impact at a rate of 2400 IPM, providing the user
with greater control and reducing the chance of overtightening
or damaging material.
When operating in reverse, the tool will impact at a normal
speed and rate of 2400 IPM. Upon sensing that the fastener has
4
broken free, the tool will cease to impact and will reduce speed
to help prevent "run-off" of loose hardware.
Low Mode
High Mode
Precision Control Mode
Anvil with Hog Ring (Fig. D)
WARNING: Use only impact accessories. Non-impact
accessories may break and cause a hazardous condition.
Inspect accessory prior to use to ensure that it contains
no cracks.
CAUTION: Inspect anvils, detent pins, and hog rings prior
to use. Missing or damaged items should be replaced
before use.
Place the forward/reverse button
position or remove battery pack before changing accessories.
To install an accessory on the hog ring anvil, firmly push
accessory onto the anvil
the accessory to slide on. After accessory is installed, the hog
ring applies pressure to help provide accessory retention.
To remove an accessory, grasp the accessory and firmly pull
it off.
7
located on the foot of the tool. The
9
which allows
MODE sELEcTIOn
Normal Impacting
RPM
High Speed Impacting RPM
Precision Control
RPM
2
in the locked off (centre)
3
8
. The hog ring
compresses to allow
EnGLIsh
1
.
0–400
0–1200
0–1900
29
Publicidad
