Publicidad
Idiomas disponibles
Idiomas disponibles
Remote Control Features And Settings
Remote Control
1. Power-up and Show all:
After inserting the batteries the display will show all symbols for
3 seconds. The remote will then enter clock set mode. Use +/- to
adjust the clock. Press CONFIRM when done. If no action is taken
within 10 seconds then the remote will exit set mode. See section
22 for clock setting instruction.
2. ON/OFF Button:
Press the ON/OFF button on the remote control to start the unit.
3. SMART Button:
(1) In SMART mode the air conditioner will automatically switch
between Cool, Heat, or Fan to maintain set temperature.
(2) When the fan is set to AUTO the air conditioner automatically
adjusts the fan speed according to room temperature.
(3) The SMART button also works to power the unit on and off.
4. COOL Button, HEAT Button and DRY Button:
(1) In COOL mode ,the unit operates in cooling. When FAN is set
to AUTO,the air conditioner automatically adjusts the fan speed
according to room temperature. COOL will be displayed during
COOL mode.
(2) In HEAT mode ,warm air will blow out after a short period of
the time due to cold-air prevention function. When FAN is set to
AUTO, the air conditioner automatically adjusts the fan speed
according to room temperature. HEAT will be displayed during
HEAT mode.
(3) DRY mode is used to reduce humidity.In DRY mode, when room
temperature becomes lower than temp. setting+2°F,unit will run
intermittently at LOW speed regardless of FAN setting. DRY will be
displayed during DRY mode.
49-5000513 Rev. 1
Mode
SMART
Initial
24°C
TEMP.
(75°F)
1
Mode
SMART
Initial
AUTO
Fan
Speed
5. FAN SPEED Button:
Fan speed selection
Press FAN SPEED button. For each press,fan speed changes as
follows:
LOW
The air conditioner fan will run according to the displayed fan
speed. When FAN is set to AUTO,the air conditioner automatically
6
adjusts the fan speed according to room temperature.
6. TEMP. +/- Buttons:
Temp+ Every time the button is pressed,the temperature setting
increases. Temp- Every time the button is pressed,temperature
setting decreases. The operating temperature range is 60°F -86°F
(16°C-30°C).
5
7. Quadrant Control
(Available on some models):
16
This setting allows the vertical airflow to be adjusted
individually on each side of the unit.
(1) Initial default positions.
SMART
Selected
Show all
Quadrant
Vertical
Position
SWING
3
Angle
(2) Press the Quadrant Control button to select the quadrant.
Each button press will select as shown below:
(3) Once desired quadrant is selected then use the Vertical Swing
button to set the direction of airflow. See section 9.
8. Vertical SWING Button:
Air Flow Direction Adjustment
Press the SWING UP/DOWN button to choose the position of the
vertical airflow louvers.
Status display of air flow
COOL/DRY
HEAT
Auto
9. Horizontal SWING Button:
Press the SWING LEFT/DOWN button to choose the position of
the hortzontal airflow louvers.
Status display of air flow
COOL/DRY/HEAT:
HEAT
COOL
DRY
24°C
24°C
24°C
(75°F)
(75°F)
(75°F)
HEAT
COOL
DRY
LOW
HI
AUTO
LOW, MED and HIGH
indicator cycles.
MED
HI
AUTO FAN SPEED
HEAT
COOL
DRY
Show
Show
Show
all
all
all
Position
Position
Position
5
3
3
Auto
Auto
FAN
Setting
temperature
is not
showed.
FAN
LOW
FAN
Show all
Positon
3
1
2
3
4
6 5
1 2 3
6
5
4
5
Publicidad
