are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
5) SERVICE
a) Have your power tool serviced by a qualifi ed
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
HOT AIR TOOL SAFETY WARNINGS
WARNING: This tool must be placed on its
stand when not in use.
A fi re may result if the appliance is not used with
care, therefore
1. be careful when using the appliance in places
where there are combustible materials;
2. do not apply to the same place for a long time;
3. do not use in presence of an explosive atmos-
phere;
4. be aware that heat may be conducted to com-
bustible materials that are out of sight;
5. place the appliance on its stand after use and
allow it to cool down before storage;
6. do not leave the appliance unattended when it
is switched on.
7. This appliance can be used by children aged
from 8 years and above and persons with re-
duced physical, sensory or mental capabilities
or lack of experience and knowledge if they
have been given supervision or instruction
concerning use of the appliance in a safe way
and understand the hazards involved.
8. Children shall not play with the appliance.
9. Cleaning and user maintenance shall not be
made by children without supervision
TECHNICAL SPECIFICATION
Model
Feature
Voltage
Power, Watt
Power switch
Power/Air flow
FEATURES
1. Power switch, fi g 1A
2. Nozzle, fi g 1B
3. Handle, fi g 1C
4. Stand for vertical operation with free hands or
storage. Fig 2D
5. Features as in technical specifi cation
USAGE
WARNING!! Read all safety warnings and all
instructions.
6
R1600
230V~ 50Hz
1600
0: OFF
1: Mid/Mid
2: High/Full
Save all warnings and instructions for future
reference.
1. Ensure the power switch is in the OFF position
before plugging into the electrical outlet.
2. Set the power switch/temperature control to the
desired speed and temperature. Let the tool run
until it reaches operating temperature.
3. With the stand the tool can be used in a vertical
position with both hands free for work.
4. Keep hands away from the immediate nozzle area,
it's hot.
PAINT AND VARNISH REMOVAL
Never use the heat gun in combination with chemical
strippers.
WARNING! LEAD PAINT FUMES ARE VERY
HARMFUL. ALWAYS PROVIDE ADEQUATE
VENTILATION WHILE WORKING INDOORS.
1. Removal of paint and varnish requires some
practice but some simple working techniques
are described here. Test on a small area of paint
before moving on to larger areas.
2. Turn on the tool and allow it to reach working tem-
perature. Hold the nozzle 70 to 100 mm from the
paint to be removed. After a short time the paint
will soften and begin to bubble. Do not overheat
the paint, as this will cause burning and make the
paint more diffi cult to remove.
3. Begin scraping the paint off. Use accessory scra-
pers. Scrape with smooth, even strokes, warming
the surface in front of the scraper by moving the
tool slightly from side to side. If paint is warmed
properly, even thick layers can be removed in a
single pass. Scrape the paint as soon as it softens
since it will quickly harden again. Figure 3
4. Clean the edge of scraper blade often.
5. Shaped or profi led surface can be stripped with a
wire brush after softening with the hot air tool.
6. Protect surfaces NOT to be heated with non-fl am-
mable material, Figure 4. Never concentrate tool's
heat on a window panel or other glass surface.
Note: The heat gun is designed to remove both oil and
latex-based paints and varnishes. It will not remove
stain or primer coat that have impregnated the surface
of wood.
OTHER JOBS FOR THE HOT AIR TOOL
1. Removing self-adhesive stickers and trim.
2. Thawing frozen pipes, frozen door locks, padlocks,
etc. Figure 5
WARNING: Be very careful when trying to
thaw plastic pipes! Pipes may melt.
3. Highlighting the natural wood grain of wooden
surfaces.
4. Fast drying of paints and varnishes.
5. Softening old putty before removal and replace-
ment.
6. Shrinking shrink wrap sheeting for packaging
protection.
7. Applying ski wax.
8. Shrinking shrink tubes on wire joints.
9. Tin soldering of wire joints etc.