Troubleshooting; Technical Specifications; Electromagnetic Compatibility - Beurer MG 115 Manual De Instrucciones

• Dispose of the device, components and optional
accessories according to applicable local regula-
tions. Unlawful disposal may cause environmen-
tal pollution.
If you have any questions, please contact the local
authorities responsible for waste disposal.

11. Troubleshooting

NOTICE:
• Repair or replacement is our only responsibility
and your only remedy under this written warranty.
Problem Cause
Massage The preset maxi-
stopped. mum period of
operation has
elapsed.
The connection to
the electrical out-
let has been inter-
rupted.
No Appliance not con-
massage. nected to the elec-
trical outlet.
Device not
switched on.
Massage device
defective.
Does not work.

12. Technical specifications

The following symbols are used on the packaging and
on the nameplate of the device and accessories.
Dimensions 11.6" x 10.4" x 5.1"
(LxWxH) (295 x 26.5 x 130 mm)
Battery operation 4 x 1.5 V type AA, Mignon (LR6)
(not included)
Device weight 23.3 oz (660 g)
Mains connection 100 – 240 V ~; 50 /60 Hz; 1.3 A
Subject to technical modifications.
FCC Statement
The device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
Remedy
Let the device cool
down for at least
15 min. before using
again. Switch the de-
vice on again.
Check the plug con-
nection and the con-
tact of the plug with
the electrical outlet.
Make all connections
and switch on the
device.
Press the Massage
button.
Switch off and un-
plug the unit imme-
diately and contact
Beurer customer
service. (Please see
warranty for service
contact)
9
NOTE: This equipment has been tested and found
to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in ac-
cordance with the instructions, may cause harmful in-
terference to radio communications. However, there is
no guarantee that interference will not occur in a partic-
ular installation. If this equipment does cause harmful
interference to radio or television reception, which can
be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit dif-
ferent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV tech-
nician for help.
Symbols Key
WARNING! Read safety information to
avoid serious injury.
Device protection class 2
Indoor use only!
Note:
If the device is used outside of the specifications, prop-
er function is no longer guaranteed! We reserve the
right to make technical changes to improve and further
develop the product.
Note:
This device and its accessories comply with US stan-
dards and are subject to special safety measures in
terms of electromagnetic tolerance. Note that portable
and mobile RF communication equipment can affect
this device. For detailed information, contact customer
service at the address provided.

ELECTROMAGNETIC COMPATIBILITY

• The device complies with current specifications with
regard to electromagnetic compatibility and is suit-
able for use in all premises, including those desig-
nated for private residential purposes. The radio fre-
quency emissions of the device are extremely low
and in all probability do not cause any interference
with other devices in the proximity.
• It is recommended that you do not place the device on
top of or close to other electronic devices. Should you
notice any interference with other electrical devices,
move the device or connect it to a different socket.