Publicidad
Idiomas disponibles
Idiomas disponibles
• Do not place any dangerous products, such as fuel, alcohol,
GB
paint, aerosol cans with a flammable propellant, flammable
or explosive substances, etc. inside or near the appliance.
• Once installed, the appliance must not be tilted at an angle
greater than 5° and it is necessary to wait 2h before connect-
ing it to the power supply to switch it on. The same applies if
the appliance is moved afterwards.
• If the appliance has been switched off or disconnected from
the power supply, it is necessary to wait 5 minutes until
switching on again.
• No other appliances should be plugged into the same socket
as with this appliance.
• Do not attempt to climb onto the appliance.
• Do not overload the interior shelves. The maximum load re-
fers to "Technical specifications"
Intended use
• This appliance is intended to be used for commercial applica-
tions, for example in kitchens of restaurants, canteens, hos-
pital and in commercial enterprises such as bakeries, butch-
eries, etc., but not for continuous mass production of food.
• The appliance is designed to keep food or beverages, under
cool state and to display them for retail sale in restaurants,
canteens, other commercial enterprises such as bakeries,
butcheries, supermarkets, etc. Any other use may lead to
damage to the appliance or personal injury.
• Operating the appliance for any other purpose shall be
deemed a misuse of the device. The user shall be solely liable
for improper use of the device.
Grounding installation
This appliance is classified as protection class I and must be
connected to a protective ground. Grounding reduces the risk
of electric shock by providing an escape wire for the electric
current.
This appliance is fitted with a power cord with grounding plug
or electrical connections with grounding wire. The connections
must be properly installed and grounded.
Main parts of the product
(Fig.1 on page 3)
1. Air outlet
2.
• Never block the air outlet. Let inside circulating cold air
flow out.
2. Rack
2.
• The height of rack is adjustable for various goods. For ad-
justment:
1) Take out the rack
2) Move the rack support on suitable height.
3) Put the rack on the support.
3. Digital controller
4. Castor
5. Air suction
2.
• Never block the suction. Air is sucked in and cold air in
circulated inside the refrigerator.
6. Glass door
7. Power Switch
Remark: The content of this manual applies for all listed items
unless specified otherwise. The appearance may vary from the
shown illustrations.
8
Control panel
(Fig.2 on page 3)
8. Up
9. Illumination
10. Refrigerant LED
11. Defrost LED
12. Set
13. Down
Circuit diagram
(Fig.3 on page 4)
A: Overheating protective probe
B: Defrost probe
C: Thermostat probe
D: Digital temperature controller
E: Display panel
F: Power switch
G: Fan Motor
H: Fan Motor
I: Lamp
J: Fan Motor
K: Overload protector
L: Compressor
M: PTC
Preparation before use
• Remove all protective packaging and wrapping.
• Check that the device is in good condition and with all ac-
cessories. In case of incomplete or damaged delivery, please
contact the supplier immediately. In this case, do not use the
device.
• Clean the accessories and the appliance before use (See ==>
Cleaning & Maintenance).
• Make sure the appliance is completely dry.
• Place the appliance on a horizontal, stable and heat resistant
surface that is safe against water splashes.
• Keep the packaging if you intend to store your appliance in
the future.
• Keep the user manual for future reference.
NOTE! Due to manufacturing residues, the appliance may emit
a light odor during the first few uses. This is normal and does
not indicate any defect or hazard. Make sure the appliance is
well ventilated.
Operating instructions
• Connect the power plug with a suitable electrical outlet. Leav-
ing the appliance for running some hours to reach the cooling
temperature before placing the beverage or food inside the
appliance.
1). Setting the temperature
• Press SET to enter into the setting mode. The set tempera-
ture is displayed.
• Press Up or Down to increase or decrease the set temper-
ature.
• Press SET again to confirm the setting and exit. Then, inside
cabinet temperature is displayed.
Publicidad
