Publicidad
• To install the speaker, first carefully remove
the grille using a straightened paperclip or
other pointed metal tool. Insert the point
into one of the grille perforations near a
corner and lift the grille free. Never use
a knife or screwdriver to pry between the
grille and the speaker frame. This will
damage your speaker.
• Loosen the rotating wall clamps by
unscrewing them. Make sure that the
rotating wall clamps are flipped inwards
so that your speaker fits into your cutout
without nicking your wall. Then place the
speaker carefully into the cutout [figure
13]. If you have a level, use it to help you
correctly align the speaker. Tighten the
wall clamp screws with a screwdriver. This
will rotate the wall clamps and secure the
speaker to the wall. Hint—on the RC55i,
RC65i and RC85i models, tighten the center
screws before tightening the corners for
the most flush fit to your wall. Do not over-
tighten the wall clamp screws [figure 14].
FIGURE 13
Place the speaker carefully into the cutout.
Coloque cuidadosamente el altavoz en el agujero.
Placez délicatement le haut-parleur dans l'ouverture.
Platzieren Sie die Lautsprecher vorsichtig in der
ausgeschnittenen Öffnung.
8
G e t m o r e i n f o r m a t i o n a n d e x c l u s i v e a c c e s s o r i e s , v i s i t w w w. p o l k a u d i o . c o m
• Carefully reinstall the grille by fitting it into
its recess so that it is just resting on the
frame. Starting with one corner, go around
the speaker and push the grille into the
grille notch a little bit at a time. Be gentle;
the grille may be easily bent out of shape
by rough handling. You will feel a positive
"snap" when it is fully in place. (Where's
the corkscrew?)
FIGURE 14
Tighten retaining wall clamps to engage wall. Use a
#2 Phillips head screwdriver or a powered screwdriver.
Apriete las prensas de retención de la pared para
enganchar el altavoz a la pared. Use un destornillador
Phillips No. 2 o un destornillador eléctrico.
Reserrez les attaches murales pour fixer solidement l'unité au
mur. Utilisez un tournevis ou une perceuse à tête Phillips no 2.
Ziehen Sie die Wandklemmen fest, um das System an der
Wand zu befestigen. Verwenden Sie dazu einen
Kreuzschlitzschraubendreher (Nr. 2) oder einen
Schraubendreher mit Motorantrieb.
SAFETY FIRST
When installing your RCi Series In-Wall
Loudspeakers, be aware of the weight of your
particular model (see specification page for
the weight of your model) and the sturdiness
of the material into which you are installing
the speaker. Also be aware of any concealed
studs, electrical wiring or plumbing in the
wall or ceiling into which you are installing
the speakers. If you are not sure of a safe
way to install these speakers, consult a
professional installer, your authorized Polk
Audio dealer, or a building contractor.
If you plan to install your RCi Series speakers
where water will directly contact them, it is
advisable to use a silicone sealant or caulk
between the frame of the speaker and the
wall surface. This seal should prevent water
from getting behind the loudspeaker and
possibly damaging the wall surface. Do not
position the speaker where water can pool
on the surface of the woofer cone or tweeter
dome, as this will great decrease the
speaker's useful life (and everything will
sound—glub! glub!—like it's coming from
under water!).
F o r C u s t o m e r S e r v i c e , c a l l 8 0 0 - 3 7 7 - 7 6 5 5 .
9
Publicidad
