Publicidad
Idiomas disponibles
Idiomas disponibles
To operate the tool, select the ON position by releasing the
trigger switch
1
and depress the lock-off control button
on the right side of the tool, as shown in Figure H.
Fig. H
1
To Operate (Fig. A, G)
Using both hands, as shown in Figure G, firmly hold the
housing
of the concrete vibrator while inserting the
3
vibrating head
4
into the poured concrete. Turn the
lock-off control button to the ON position and depress
trigger switch.
For best results, it is usually best to keep the vibrator head
vertical at all times and to avoid side-to-side movement. It is
generally best to insert the vibrator head into the concrete,
turn the vibrator on, then turn it off before pulling the
vibrator head straight out. Move the vibrator head to the
next location and repeat.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Flex Shaft Lubrication
The flex shaft casing is properly lubricated at the factory. It is
recommended for every 100 hours of use, the flex shaft core
be removed and wiped with a clean, dry cloth and high-
temperature grease be applied.
Use caution to avoid dirt and other contaminates from
entering the casing or touching the core when removing
and cleaning the flex shaft core. Avoid low-temperature
grease which may collect at the bottom of the shaft
causing leaks.
Do not disassemble vibrator head. The vibrator head
is sealed at the factory and contains a special high-
performance lubricant. Breaking the seal and adding
incorrect lubricant will significantly decrease the
performance and life of the tool. If vibrator head is damaged
or needs lubricant, take the tool to a D
service center.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
2
2
Accessories
Recommended accessories for use with your tool
are available at extra cost from your local dealer or
authorized service center. If you need assistance in
locating any accessory, please contact D
Tool Co., 701 East Joppa Road, Towson, MD 21286, call
1-800-4-D
www.dewalt.com.
Repairs
The charger and battery pack are not serviceable.
Register Online
Thank you for your purchase. Register your product now for:
•
•
•
Register online at www.dewalt.com/register.
Three Year Limited Warranty
D
WALT will repair, without charge, any defects due to
e
faulty materials or workmanship for three years from the
date of purchase. This warranty does not cover part failure
WALT authorized
e
due to normal wear or tool abuse. For further detail of
warranty coverage and warranty repair information, visit
www.dewalt.com or call 1-800-4-D
This warranty does not apply to accessories or damage
caused where repairs have been made or attempted by
others. This warranty gives you specific legal rights and
you may have other rights which vary in certain states
or provinces.
In addition to the warranty, D
by our:
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
WARNING: Since accessories, other than those
offered by D
WALT, have not been tested with this
e
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
WALT (1-800-433-9258) or visit our website:
e
WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement) should
be performed by a D
WALT factory service center
e
or a D
WALT authorized service center. Always use
e
identical replacement parts.
WARRAnTY sERViCE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with your product.
COnFiRMATiOn OF OWnERshiP: In case of
an insurance loss, such as fire, flood or theft, your
registration of ownership will serve as your proof
of purchase.
FOR YOUR sAFETY: Registering your product will
allow us to contact you in the unlikely event a safety
notification is required under the Federal Consumer
Safety Act.
WALT tools are covered
e
English
WALT
e
WALT Industrial
e
WALT (1-800-433-9258).
e
9
Publicidad
