Publicidad
PL900 SPEAKER SYSTEM:
Contents of Carton:
1 Tower Speaker
HOW TO PLACE YOUR SYSTEM COMPONENTS: The optimum listening
position is at the tip of the so-called "stereo triangle"(Fig.1). The equilibrium
between the right and left stereo channels is best in this position, providing the
most balanced and realistic sound reproduction.Your AR speakers will operate
most efficiently when they are located in parts of the room with "hard"
acoustics, i.e., areas including hard, smooth surfaces such as walls and wooden
furniture. The speakers should radiate the sound from this hard area into the
"softer" parts of the room containing sound-absorbing elements such as
upholstered furniture, carpets and so on. Make sure that there are no
sound-absorbing obstacles between the speakers and your listening position,
as this will muffle the sound and impair your listening pleasure.Your PL900
Series speakers are fully shielded for use in audio/video applications. This
allows you to place any of the speakers next to the television without affecting
picture quality. If you are using other speakers, be sure to locate them at least 3
feet away from the television to avoid interference to the set's picture. The
speakers should be installed at least 1 foot away from the side walls. This
prevents exaggerated "booming" bass and helps to produce more balanced,
detailed sound reproduction.If possible, the speakers should be installed so that
the tweeters are on the same level as the listener's ears. If you install the
speakers in a wall unit, take care to ensure that the fronts of the speakers are
flush with the front of the wall unit.
CONNECTING THE SURROUND SPEAKERS: Strip the insulation from the
connection cable ends and twist the ends tightly or tin them with solder. Then
insert the ends in the connection terminals and secure them. Caution: Take
care to ensure that the speaker cables are connected with the correct
polarity!Connect the negative amplifier output terminal (black) to the negative
connection terminal of the AR speaker (also black). Proceed in the same way to
connect the positive terminals, which are normally red. Standard speaker
connection cables normally have a colored marking or indentation in the surface
of the insulation to distinguish the two leads from one another.
IMPORTANT: Always connect the red (+) terminal on the Receiver to the red (+)
terminal on the corresponding Speaker i.e. Front Left. Connect the
corresponding black (-) terminal on the Receiver to the black (-) terminal on the
same Speaker. Continue until all of the speakers have been connected in this manner.
fig 1
CENTER FRONT
CENTRE-AVANT
LEFT FRONT
RIGHT FRONT
CENTRO FRONTAL
AVANT DROIT
AVANT GAUCHE
FRONTAL IZQUIERDO
FRONTAL DERECHO
SUBWOOFER
HAUT-PARLEUR
DE GRAVES
ALTAVOZ DE
SUBGRAVES
LISTENING AREA
ZONE DʼÉCOUTE
CAMPO AUDITIVO
LEFT REAR
ARRIÈRE
RIGHT REAR
GAUCHE
ARRIÈRE DROIT
POSTERIOR
POSTERIOR
IZQUIERDO
DERECHO
CONNECTION WITH SPEAKER WIRE
RECEIVER
FRONT LEFT
FRONT RIGHT
SPEAKER
SPEAKER
TOWER STAND-MOUNTING WITH WIRE: (fig 2)
fig 2
STEP 1 – Screw the provided lock-nuts onto both
threaded ends of the stand tube.
STEP 2 – Thread end of your speaker wire
through the stand tube starting by fishing
the wire through the hole on the top of the tube.
Step 3 – Screw the stand tube into the base and
tighten. use the threaded lock nut to tighten the
tube against the base making sure the wire
management hole is facing the back of the stand
STEP 4 – Connect the speaker to the stand by
Hex Nut
turning the speaker clockwise until it is tight
and lined up with the base. Tighten the lock-nut
against the speaker and lock it into place.
STEP 5 – Connect the speaker wire to the 5-way
binding posts making sure the positive and
negative wires are connected properly. Failure to
match the polarity will result in the
speakers being out of phase.
TOWER WALL-MOUNTING: (fig 3)
STEP 1 – After marking the level location on the
Round Nut
wall, mount the wall plate to the wall
using the proper hardware for your type of wall.
Make sure your screws are securely mounted into
the wall studs or that the proper anchors are
Hex Nut
used for a hollow wall application.
STEP 2 – Securely fasten the bracket heads to
the back of the speaker using the
included hardware.
STEP 3 – Connect the two bracket components together by placing the
mounting pins on the wall plate into the bracket heads mounted to the back of
the speaker.
STEP 4 – Adjust the speaker positioning by swiveling left or right to create a
focused listening position.
fig 3
NO SOUND FROM THE FRONT SPEAKERS.
•
Be sure the Receiver's POWER Switch is in the ON position.
•
Check the Receiver's Volume Control Setting - if it is all the way down,
there won't be any sound.
•
Check that the Receiver's Input Selector is set to an active source of
audio signals and that a Tape Monitor Loop is not engaged.
•
Be sure that the Receiver's Speaker Selector switch is turned to the
position [A or B, 1 or 2] that you have your Front speakers connected
to. If the Receiver has a headphone jack, you can use headphones to
check the Receiver for output.
ATTENTION IMPORTANT SAFETY PRECAUTIONS:
Please read these instructions thoroughly before attempting to operate your AR
Surround System.Be sure to save this manual for future reference. Also save your
bill of sale, as it may be required for warranty service.
CLEANING:
Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
ATTACHMENTS:
Do not use attachments not recommended by AR as they may cause hazards.
WATER and MOISTURE:
Do not use the AR Speaker System near water - for example: near a bath tub, wash
bowl, kitchen sink, or laundry tub; in a wet basement,near a swimming pool, or similar
locations.
HEAT:
The AR Surround System should be situated away from heat sources such as radiators, heat
registers, stoves, or other products (including amplifiers) that produce heat.
ACCESSORIES:
Do not place the AR Speaker System on an unstable cart, stand, tripod, bracket or
table. The product may fall, causing serious injury to a child or adult, and serious
damage to the product. Use only with brackets and stands recommended by AR or
sold with the AR Speaker System. Any mounting of the speakers should follow AR's
instructions and should use a mounting accessory recommended by AR.
OBJECT AND LIQUID ENTRY:
Never push objects of any kind into this product through openings as they may
touch dangerous voltage points or short-out parts that could result in a fire or
electric shock. Never spill liquid of any kind on the AR Speaker System.
SPECIFICATION:
Tower:
Driver Comp: 3 Way Satellite
Woofer: (4) 4" Aluminum
Midrange: 2" Silk Dome
Tweeter: 30mm super tweeter
Freq Response: 100Hz-50kHz
Sensitivity: 91dB
Impedance: 8 Ohms
Rec. Power: 5-150 watts
Dimensions: 24.25" H x 5.25"W x 4.375" D
Publicidad
