Calypso Watches IKMK5839 Manual De Instrucciones página 3

I
ENGLISH INSTRUCTION MANUAL
BUTTONS
The operation of buttons are indicated by using the letters shown in the illustration.
A -- Reset
B -- Mode
C -- EL backlight
D -- Start / Stop
DISPLAY
The screen shown in below:
Day of week
Hour
Chime
BACKLIGHT
The backlight that uses an EL (electro-luminescent) cause
the display to glow for easy reading in the dark.
Use EL Backlight
• In any mode, press "C" to illuminate the display about 3
seconds.
ALARM
Alarm and Chime
• In the alarm mode, press "D" to on/off the alarm and chime in the following
sequences: Alarm & Chime off - Alarm on Chime on - Alarm & Chime on
Alarm Time Setting
1. In the alarm mode, press "A" the hour to flash, the indicator "
(flashing indicated in set mode.
2. Press "D" to increase the hour, press and hold to increase at high speed.
3. Press "B" to select the minutes.
4. Press "D" to increase the minutes,press and hold to increase at high speed.
5. Press "A" to exit the set state, after you set.
• The alarm sounds at the preset time each day for about 60 seconds, press
any button to break it.
DUAL TIME
Dual Time Setting
1. In the dual time mode, press "A" the hour to flash (flashing indicated in set mode).
2. Press "D" to increase the hour, press and hold to increase at high speed.
3. Press "B" to select the minutes.
4. Press "D" to change the minutes(press once change 30 minutes).
5. Press "A" to exit the set state, after you set..
By virtue of the regulations pursuant to the handling of waste products deriving from electronic and electrical equipment, end of lifecycle watch making
products must be selectively collected for processing. You may therefore dispose of your quartz watch making products at any of our retail outlets or any other
authorized collection point. The selective collection, processing, rating and recycling of these products helps contribute to safeguarding the environment and
protecting our health.
MODE SELECTION
Press "B" to change mode to mode in the following Sequence:
Timekeeping Mode - Alarm Mode - Stopwatch Mode - Dual Time Mode.
TIMEKEEPING
• 12/24H Format
• Hour, Minutes,
Seconds, Day of week,
Date.
• 100 years Calendar
(2000 ~ 2099).
STOPWATCH
• 1/100 second unit;
• Measuring range:
0'0"00~23:59'59".
TIMEKEEPING
12/24H Format
Date
• In the timekeeping mode, press "A" to
switch between 12/24H formats.
Minutes
Seconds
Alarm
STOPWATCH
A Lap Time
1. In the stopwatch mode, press "D" to start
the stopwatch.
2. To stop the stopwatch by pressing "D"
again.
3. Press "A" to reset the stopwatch
" appear
CARE OF YOUR WATCH
1. This watch contains electronic components. Never attempt to open the case or remove the
back cover.
2. Do not operate push buttons below the surface of the water while swimmingor diving.
3. Should water or condensation appear in the water, have the water checked immediately.
Corrosion of electronic parts can occur inside the case.
4. Avoid severe impact. The watch is designed to withstand impact under normal use. It is
inadvisable to subject it to severe impact or rough usage.
5. Avoid exposing the watch to extreme temperature.
6. Clean the watch with soft cloth and clean water only. Avoid using chemicals.
7. Keep your watch away from the conditions of strong electricfield and static electricity.
IKMK5839
ALARM
• Hourly time signal.
• The alarm sounds at the
preset time each day
DUAL TIME
• The time for other time
zone
Calendar
• In the timekeeping mode, press and hold "D"
to display: Year, Month, Date.
Time Setting
1. In the timekeeping
mode,press and hold "A"
until the seconds to flash
(flashing indicated in set
mode).
2. Press "D" to reset the
seconds.
3. Press "B" change to the
next selection.
Split Time
1. In the stopwatch mode,press "D" to start
the stopwatch.
2. Press "A" to display the split time,
stopwatch timing continues internally.
3. Press "A" to clear the split time and to
continue time measurement.
4. Repeat step 2 and 3, you can measure
themulti split time.
5. Press "D" to stop the stopwatch.
4. Press "D" to increase the
number, press and hold to
increase at high speed.
5. Repeat step 3 and 4, the
selection in the following
sequence: Seconds - Hour -
Minutes - Year Month - Date.
6. Press "A" to exit the set state,
after you set(The day of week
is automatically displayed in
accordance with year, month
and date setting).