Publicidad
Idiomas disponibles
Idiomas disponibles
Anleitung_GE_PM_51_VS_H_BS_ECO_SPK7__ 29.11.13 08:37 Seite 26
GB
7. Operation
Note:
For detailed information on starting the engine,
refer to the enclosed manual from Briggs &
Stratton.
Important.
The engine does not come with oil in it.
Therefore, be sure to add oil before starting the
engine. You will also need to fill in petrol, as this
is also not supplied upon delivery.
In order to avoid any unintentional start-ups of the
lawn mower, it comes equipped with an engine
brake (Fig. 10/Item 1) which must be pulled back
before the engine can be started. When the engine
control lever is released it must return to its initial
position, at which point the engine automatically
switches off.
You can control the rotation speed of the blade using
the speed lever (Fig. 14).
Before you start mowing, you should run through
this operation several times in order to ensure that
the machine is working properly.
Whenever you need to perform any kind of adjust-
ment and/or repair work on your lawn mower, wait
until the blade has come to a complete stop.
Always switch off the engine before carrying out any
adjustments, maintenance or repairs.
Note:
1. Engine brake (Fig. 10/Item 1): Use the lever to
stop the engine. When you release the lever the
engine and the blade stop automatically (Fig.
10). To mow, hold the lever in the working
position. Before you start to mow, check the
start/stop lever several times to be sure that it is
working properly. Ensure that the tension cable
can be smoothly operated (i.e. is not catching or
kinking in any way).
2.
Speed lever (Fig. 14): Move this lever in order to
increase or decrease the engine speed. (Tortoise
= Slow / Hare = Fast)
3. Drive lever (clutch lever) (Fig. 11/Item 19): If you
press this (Fig. 11) the clutch for the drive will be
closed and the lawnmower will start to move with
the motor running.
Release the drive lever in good time to stop the
moving lawnmower. Practice starting and
stopping before you use the mower for the first
time until you are familiar with controlling the
mower.
4. Caution: The blade begins to rotate as soon as
the engine is started.
26
Important:
Before you start the engine, move the motor
brake several times to be sure that the stop
cable is properly working. Note: The engine is
factory set to a speed that is optimal for cutting
and blowing grass into the basket and is
designed to provide many years of use.
5. Check the oil level.
6. Fill the tank with petrol when it is empty, using a
funnel and measuring vessel. Make sure that the
petrol is clean.
Note: Use only unleaded petrol as fuel.
Warning: Never use more than one safety petrol
can. Do not smoke when refueling. Switch off the
engine before refueling and allow the engine to cool
down for a few minutes.
Mulching
In the mulching mode the cuttings are shredded in
the enclosed mower housing and then spread back
onto the lawn. It is not necessary to gather and
dispose of the grass.
Important: Mulching is only possible if the lawn is
relatively short. Optimum results can be achieved
only with a mulching blade (available as an
accessory).
To use the mulching function, disconnect the debris
bag, slide the mulching adaptor into the ejector
opening (Fig. 12/Item 22) and close the ejector
opening.
Side ejector
You should fit the mulching adaptor (Item 22) in
order to use the side ejector. Connect the side
ejector adaptor (Fig. 13/Item 21) as shown in Figure
13.
Filling level indicator debris bag
The debris bag is equipped with a filling level
indicator (Fig. 2/Item 6). This will be opened by the
air current produced by the mower. If the flap falls
during mowing, the debris bag is full and should be
emptied. To ensure that the filling level indicator
works properly, the holes under the flap must be kept
clean and permeable.
Adjusting the running speed (vario speed)
It is possible to set up to four (4) different running
speeds. The lowest speed corresponds to Stage 1,
the fastest speed corresponds to Stage 4.
To adjust the speed, move the lever (Fig. 23/Item 24)
into the desired position.
Important! To adjust the running speed the engine
must be running and the control lever (Item 19) must
have been activated!
Publicidad
