Publicidad
Idiomas disponibles
Idiomas disponibles
CHARGING PROCEDURE
NOTE: Before using the tool, read the
instruction book carefully.
CHARGING INSTRUCTIONS
1. CHARGING YOUR BATTERY PACK
WARNING: The charger and battery pack
are specifically designed to work together so
do not attempt to use any other devices.
Never insert or allow metallic objects into your
charger or battery pack connections because an
electrical failure and hazard will occur.
2. BEFORE USING YOUR CORDLESS TOOL
Your battery pack is partly charged and needs to be fully
charged before first use.
3. HOW TO CHARGE YOUR BATTERY
CHARGING PROCEDURE
1)
Plug the charger into an appropriate outlet
(120 V).
2)
Slide the battery pack into the charger as
shown in illustration A., the LIGHT will become
green and flash to show charging has started.
3)
After charging approx. 40 mins (2.0Ah)/ 50 mins
(2.5Ah)/80 mins (4.0 Ah)/100 mins (5.0Ah) for
KA3712; 25 mins (2.0Ah)/ 30 mins (2.5Ah)/50
mins (4.0 Ah)/60 mins (5.0Ah) for KA3714, the
light will stay green without flashing, which
means the battery is fully charged.
WARNING: When battery charge runs out
after continuous use or exposure to direct
sunlight or heat, allow time for the battery
to cool down before re-charging to achieve the
full charge.
CHARGING INDICATOR
This charger is a "smart charger" that is designed
to provide you information on the status of your
battery charge. Indicator lights n the table below will
show the charging status.
If you receive a defective battery indication light (red
on), insert a new battery to determine if the charger
is OK. If the new battery charges correctly, then the
original pack is defective and should be returned to
a service center or recycling service center. If the
new battery pack displays the same problem as the
original Battery Pack, have the charger tested at an
authorized service center.
Light
ON/Flash
Red on
Status
Defective Battery
----------
Red flash
Green on
----------
Green flash
BATTERY TEMPERATURE PROTECTION
This charger has a battery temperature protection
feature. When the charger detects a battery pack that
is too hot (the light will be red and flash), its internal fan
will rapidly cool the battery to the correct temperature.
When the charger detects a battery pack that is too cold
(the light will be red and flash), it automatically activates
the protection circuit, and suspends charging until the
battery pack has reached the correct temperature .The
charging process will then automatically begin (the light
will be green and flash). This feature ensures maximum
battery life.
LEAVING THE BATTERY PACK IN THE
CHARGER
If a fully charged battery pack is left in the charger, the
Light will remain green. The battery pack will remain
charging with a maintenance trickle current.
DEFECTIVE BATTERY PACKS
This charger will detect a defective battery pack. When
a defective battery pack is inserted into the charger, the
charger will try to repair it. This process will last about
30mins (the light will be green and flash). If the repair
is successful, the charger will automatically begin to
charge the battery pack to the highest capacity possible
(the light will be green and flash). If the light becomes
solid red, the battery pack is dead.
NOTE: Repaired battery packs are still usable but
should not be expected to perform as much work as
new battery packs.
MOUNTING CHARGER ONTO THE
WALL
Install screws (not provided) in the wall .Use screws
sufficiently strong to hold the combined weight of the
charger and battery pack. (See Fig. B)
IMPORTANT CHARGING NOTES:
1.
For a new battery or a battery that has been
in storage for sometime, please recharge the
battery before use. If you want to store the
battery for a long time, please fully charge the
battery pack to ensure maximum battery life.
Battery Temperature
Protection.
The temperature of
battery pack is less
32
F(0
C)
0
0
than
or more
140
F(60
C)
0
0
than
.
Fully Charged
Charging
7
EN
Publicidad
