Oxygenated Fuels; Charging The Battery Pack - Ryobi RY29550 Manual Del Operador

FILLINg TANK
 C l e a n s u r f a c e a ro u n d f u e l c a p t o p re v e n t
contamination.
 Loosen fuel cap slowly. Rest the cap on a clean
surface.
 Carefully pour fuel into the tank. Avoid spillage.
 Prior to replacing the fuel cap, clean and inspect the
gasket.
 Immediately replace fuel cap and hand tighten. Wipe up
any fuel spillage.
NOTE: It is normal for smoke to be emitted from a new
engine after first use.
WARNINg:
Always shut off engine before fueling. Never add fuel to
a machine with a running or hot engine. Move at least
30 ft. from refueling site before starting engine. Do not
smoke! Failure to heed this warning could result in seri-
ous personal injury.

OXYgENATED FUELS

Some conventional gasolines are blended with alcohol or an
ether compound. These gasolines are collectively referred
to as oxygenated fuels. To meet clean air standards, some
areas of the United States and Canada use oxygenated fuels
to help reduce emissions.
If using an oxygenated fuel, make sure it is unleaded and
meets the minimum octane rating requirements. Before using
an oxygenated fuel, try to confirm the fuel's contents. Some
states/provinces require this information to be posted on the
pump. The following are the EPA approved percentages of
oxygenates:
Ethanol (ethyl or grain alcohol) 10% by volume. You
may use gasoline containing up to 10% ethanol by volume.
Gasoline containing ethanol may be marketed under the
name "Gasohol." Do not use E85 fuel.
MTBE (methyl tertiary butyl ether) 15% by volume. You
may use gasoline containing up to 15% MTBE by volume.
Methanol (methyl or wood alcohol) 5% by volume. You
may use gasoline containing up to 5% methanol by volume
as long as it also contains cosolvents and corrosion inhibitors
to protect the fuel system. Gasoline containing more than 5%
methanol by volume may cause starting and/or performance
problems. It may also damage metal, rubber, and plastic
parts of the product or your fuel system.
If you notice any undesirable operating symptoms, try another
service station or switch to another brand of gasoline.
NOTE: Fuel system damage or performance problems
resulting from the use of an oxygenated fuel containing more
than the percentages of oxygenates stated previously are
not covered under warranty.
OPERATION
cAUTION:
If at any point during the charging process none of the
LEDs are lit, remove the battery pack from the charger
to avoid damaging the product. DO NOT insert another
battery. Return the charger and battery to your nearest
service center for service or replacement.

cHARgINg THE BATTERY PAcK

The battery pack for this tool has been shipped in a low
charge condition to prevent possible problems. Therefore,
you should charge overnight prior to use.
NOTE: Batteries will not reach full charge the first time they
are charged. Allow several cycles (operation followed by
recharging) for them to become fully charged.
 Charge battery pack only with the charging assembly
provided.
 Make sure power supply is normal household voltage,
120 V, Ac only, 60 Hz.
 Connect charger to power supply.
 Place battery pack in charging stand. Align raised rib
on battery pack with groove in charging stand. See
Figure 7.
 Press down on battery pack to be sure contacts on battery
pack engage properly with contacts in charging stand.
 The charge indicator light (LED), located on the charging
stand, will light up red and glow when the charger
is properly connected to power supply. This light
indicates the charger is operating properly. It will remain
on until battery pack is removed from charging stand or
charger is disconnected from power supply.
 After normal usage, 3 hours or less of charging time is
required to fully recharge battery pack.
 If both red and orange LED indicators glow, the
battery pack is deeply or completely discharged, and
6 hours or longer of charging time is required to fully
recharge battery pack.
NOTE: If charger does not charge battery pack or orange
LED continues to glow after more than 30 minutes of
charging, return battery pack and charging assembly to
your nearest Ryobi Authorized Service Center for electrical
check.
 The battery pack will become slightly warm to the touch
while charging. This is normal and does not indicate a
problem.
 Do not place charger in an area of extreme heat or cold.
It will work best at normal room temperature.
 When batteries become fully charged, unplug charger
from power supply and remove the battery pack.
9 — English