Hitachi Koki DS 14DL2 Instrucciones De Manejo página 11

STANDARD ACCESSORIES
1 Plus driver bit (No.2) .................... 1
2 Charger (UC18YMRL or UC18YRL) ... 1
3 Battery ............................... 1 or 2 or 3
DS14DL2
4 Plastic case ....................................... 1
5 Side handle ....................................... 1
1 Plus driver bit (No.2) .................... 1
2 Charger (UC18YMRL or UC18YRL) ... 1
DS18DL2 3 Battery ............................... 1 or 2 or 3
4 Plastic case ....................................... 1
5 Side handle ....................................... 1
1 Plus driver bit (No.2) .................... 1
2 Charger (UC18YRL) ......................... 1
DV14DL2 3 Battery ............................... 1 or 2 or 3
4 Plastic case ....................................... 1
5 Side handle ....................................... 1
1 Plus driver bit (No.2) .................... 1
2 Charger (UC18YRL) ......................... 1
3 Battery ............................... 1 or 2 or 3
DV18DL2
4 Plastic case ....................................... 1
5 Side handle ....................................... 1
DS14DL2 (NN)
DS18DL2 (NN) Without charger, battery, and plastic
DV14DL2 (NN) case.
DV18DL2 (NN)
Standard accessories are subject to change without
notice.
OPTIONAL ACCESSORIES (sold separately)
Battery
(BCL1430) (EBM1830)
(BCL1440) (BCL1840)
Optional accessories are subject to change without notice.
APPLICATIONS
<DS14DL2 / DS18DL2>
Driving and removing of machine screws, wood
screws, tapping screws, etc.
Drilling of various metals
Drilling of various woods
<DV14DL2 / DV18DL2>
Drilling of brick and concrete block, etc.
Driving and removing of machine screws, wood
screws, tapping screws, etc.
Drilling of various metals
Drilling of various woods
BATTERY REMOVAL/INSTALLATION
1. Battery removal
Hold the handle tightly and push the battery latch to
remove the battery (see Figs. 1 and 2).
CAUTION:
Never short-circuit the battery.
2. Battery installation
Insert the battery while observing its polarities (see Fig. 2).
CHARGING
Before using the power tool, charge the battery as follows.
1. Connect to the power source
When charging the battery from an AC power source
Connect the charger's power cord to the receptacle.
When connecting the plug of the charger to a
receptacle, the pilot lamp will blink in red (At 1-
second intervals).
CAUTION:
Do not use the electrical cord if damaged. Have it
repaired immediately.
When charging the battery from a DC 12V in-car power
source (UC18YMRL)
Secure the battery charger in place in the car.
Use the strap supplied with the battery charger to
fasten the battery charger in place and prevent it
from moving inadvertently. (See Fig. 25)
CAUTION:
Do not place the battery charger or battery under
the driver's seat. Secure the battery charger in
place to prevent it from moving inadvertently as
this may lead to an accident.
Insert the cigarette lighter connecting plug into the
cigarette lighter socket.
If the plug is loose and falls out of the cigarette
lighter socket, repair the socket. As the socket may
be faulty, you are recommended to contact your
local car dealer. Continued use of the socket may
result in an accident due to overheating. (Fig. 3)
2. Insert the battery into the charger.
Firmly insert the battery into the charger till it contacts
the bottom of the charger and checking the polarities
as shown in Fig. 3.
CAUTION:
If the batteries are inserted in the reverse direction,
not only recharging will become impossible, but it
may also cause problems in the charger such as a
deformed recharging terminal.
3. Charging
When inserting a battery in the charger, charging will
commence and the pilot lamp will light continuously
in red.
When the battery becomes fully recharged, the pilot
lamp will blink in red. (At 1-second intervals) (See
Table 1)
(1) Pilot lamp indication
The indications of the pilot lamp will be as shown in
Table 1, according to the condition of the charger or
the rechargeable battery.
English
Fig. 25
10