Publicidad
Safety Information
Products marked with a crossed-out wheeled bin symbol and
a single black bar underneath, contain parts that must be han-
dled in compliance with the WEEE Directive. The entire
product, or the WEEE parts, can be sent to your "Customer
Center" for handling.
FCC and ISED Compliance Statement
This device complies with Part 15 of the FCC Rules. Any
changes or modifications not expressly approved by the man-
ufacturer could void the user´s authority to operate this de-
vice.
Operation is subject to the following two conditions:(1) this
device may not cause harmful interference, and (2) this device
must accept any interference received, including interference
that may cause undesired operation.
FCC Responsible party:
Name: Rodney Hill
Position: Product Marketing Manager
Address: 3301 Cross Creek Parkway
MI 483 26 Auburn Hills
United States
Mobile: +1 919 272 7837
Email: rodney.hill@us.atlascopco.com
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interfer-
ence when the equipment is operated in a commercial en-
vironment. This equipment generates, uses, and can radi-
ate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause
harmful interference in which case the user will be re-
quired to correct the interference at his own expense.
ISED Compliance Statement:
This device complies with: CAN ICES-3 (A)/NMB-3(A)
(English) This device complies with Industry Canada's li-
cence-exempt RSSs. Operation is subject to the following two
conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including inter-
ference that may cause undesired operation of the device.
(French) Le présent appareil est conforme aux CNR d'Indus-
trie Canada applicables aux appareils radio exempts de li-
cence. L'exploitation est autorisée aux deux conditions suiv-
antes:
1) l'appareil ne doit pas produire de brouillage;
2) l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le
fonctionnement.
4
© Atlas Copco Industrial Technique AB - 9836 3967 00
Information Regarding Article 33 in REACH
The European Regulation (EU) No. 1907/2006 on Registra-
tion, Evaluation, Authorization and restriction of Chemicals
(REACH) defines among other things requirements related to
communication in the supply chain. The information require-
ment applies also to products containing so called Substances
of Very High Concern (the "Candidate List"). On 27 June
2018 lead metal (CAS nr 7439-92-1) was added to the Candi-
date List.
In accordance with the above this is to inform you that certain
electrical and mechanical components in the product may
contain lead metal. This is in compliance with current sub-
stance restriction legislation and based on legit exemptions in
the RoHS Directive (2011/65/EU). Lead metal will not leak
or mutate from the product during normal use and the concen-
tration of lead metal in the complete product is well below the
applicable threshold limit. Please consider local requirements
on the disposal of lead at product end of life.
Regional Requirements
WARNING
This product can expose you to chemicals including lead,
which is known to the State of California to cause cancer
and birth defects or other reproductive harm. For more
information go to
https://www.p65warnings.ca.gov/
UK DECLARATION OF CONFORMITY
We, Atlas Copco Industrial Technique AB,
SE-105 23 STOCKHOLM SWEDEN, declare
under our sole responsibility that the product
(with name, type and serial number, see front
page) is in conformity with the following UK
Regulation(s):
S.I. 2008/1597, S.I. 2012/3032, S.I. 2016/1091
Designated Standards applied:
EN 55014-1:2017 + A11:2020, EN
55014-2:2015, EN 61000-6-2:2005+AC:2005,
EN 61000-6-2:2019, EN
62841-1:2015+AC:2015, EN 62841-2-2:2014
+AC:2015
Authorities can request relevant technical information from:
Aleksandra Duric, Product Compliance Manager, Atlas
Copco Industrial Technique AB, SE-105 23 Stockholm Swe-
den
Stockholm, 6 March 2023
Carl von Schantz, Managing Director
Signature of issuer
Authorised Representative UK
James McAllister, General Manager
ETD ST101-150-20-T25
Publicidad
