Publicidad
Idiomas disponibles
Idiomas disponibles
d) use special care when working corners, sharp edges etc. avoid bouncing and snagging
the accessory. Corners, sharp edges or bouncing have a tendency to snag the rotating
accessory and cause loss of control or kickback.
e) Do not attach a saw chain woodcarving blade or toothed saw blade. Such blades create
frequent kickback and loss of control.
SAFETY WARNINgS SPECIFIC FOR gRINdINg ANd AbRASIvE CUTTINg-OFF
OPERATIONS
a) use only wheel types that are recommended for your power tool and the specific guard
designed for the selected wheel. Wheels for which the power tool was not designed cannot
be adequately guarded and are unsafe.
b) the grinding surface of center depressed wheels must be mounted below the plane of the
guard lip. An improperly mounted wheel that projects through the plane of the guard lip cannot
be adequately protected.
c) the guard must be securely attached to the power tool and positioned for maximum
safety, so the least amount of wheel is exposed towards the operator. The guard helps to
protect operator from broken wheel fragments, accidental contact with wheel, and sparks that
could ignite clothing.
d) Wheels must be used only for recommended applications. for example: do not grind
with the side of cut-off wheel. Abrasive cut-off wheels are intended for peripheral grinding;
side forces applied to these wheels may cause them to shatter.
e) always use undamaged wheel flanges that are of correct size and shape for your selected
wheel. Proper wheel flanges support the wheel thus reducing the possibility of wheel breakage.
Flanges for cut-off wheels may be different from grinding wheel flanges.
f) Do not use worn down wheels from larger power tools. Wheel intended for larger power tool is not
suitable for the higher speed of a smaller tool and may burst.
AddITIONAL SAFETY WARNINgS SPECIFIC FOR AbRASIvE CUTTINg-OFF
OPERATION
a) Do not "jam" the cut-off wheel or apply excessive pressure. Do not attempt to make an
excessive depth of cut. Overstressing the wheel increases the loading and susceptibility to
twisting or binding of the wheel in the cut and the possibility of kickback or wheel breakage.
b) Do not position your body in line with and behind the rotating wheel. When the wheel, at
the point of operation, is moving away from your body, the possible kickback may propel the
spinning wheel and the power tool directly at you.
c) When wheel is binding or when interrupting a cut for any reason, switch off the power
tool and hold the power tool motionless until the wheel comes to a complete stop. never
attempt to remove the cut-off wheel from the cut while the wheel is in motion otherwise kickback
may occur. Investigate and take corrective action to eliminate the cause of wheel binding.
d) Do not restart the cutting operation in the workpiece. let the wheel reach full speed
and carefully reenter the cut. The wheel may bind, walk up or kickback if the power tool is
restarted in the workpiece.
e) Support panels or any oversized workpiece to minimize the risk of wheel pinching and
kickback. Large workpieces tend to sag under their own weight. Supports must be placed under
the workpiece near the line of cut and near the edge of the workpiece on both sides of the wheel.
f) use extra caution when making a "pocket cut" into existing walls or other blind areas. The
protruding wheel may cut gas or water pipes, electrical wiring or objects that can cause kickback.
g) it is recommended to use grinding/cutting wheels no thicker than 1/16" (1.7 mm) thick.
AddITIONAL SAFETY INFORmATION
• Do not use type 1/41 flat cut-off abrasive or diamond wheels without proper guard.
Warning:
always wear proper personal hearing protection that conforms to anSi
S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this product
may contribute to hearing loss.
Warning:
alWayS use safety glasses. Everyday eyeglasses are NOT safety glasses. Also use
face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3),
4
Publicidad
