Publicidad
Idiomas disponibles
Idiomas disponibles
GRILLO S.p.A.
Via Cervese 1701 – 47521 CESENA (FC) ITALY
Tel. 0039 – 0547 – 633.111 / Fax 0039 – 0547 – 632.011
Web site: www.grillospa.it / e-mail:
MODEL: hydrostatic lawnmower with front cutting deck.
ENGINE: YANMAR 4TNV88, diesel 2190 cm³ (max. 44 HP at 2600 revolutions), 4 cylinders, liquid cooling system
with hydraulic fan, equipped with automatic radiator cleaning device.
FUEL TANK: 35 litres.
HYDRAULIC OIL TANK: 25 litres.
HOURLY CONSUMPTION: 7,5 litres approximately.
STARTER: electric 12V.
TRACTION: hydraulic, 4 wheel drive (permanent with anti skid).
MANUAL (WITH PUSH-BUTTON) AND SELF-ENGAGING DIFFERENTIAL LOCK.
GEARBOX: hydrostatic transmission with 4 hydraulic engines on the 4 wheels.
STEERING SYSTEM: hydraulic drive with steering wheel.
CLUTCH: hydraulic, electrically activated for PTO, with blade brake.
SPEED: 0-20 km/h: continuous variation.
WHEELS: front 24 x 12.00-12; rear 20 x 10.00-10.
MOTORISED BAFFLE PROVIDES FULL AND EVEN GRASS-CATCHER FILLING.
GRASS CATCHER: 1200 litres.
DISCHARGE HEIGHT: 2100 mm, REAR PROJECTION: 500 mm.
LOADING ACCELERATOR: diameter 400 mm with hydraulic engine with safety valve against accidental impacts,
independent activation.
AUTOMATIC FEATURES: automatically disengagement of blades and loading accelerator when the grass catcher
is full.
BRAKE: hydraulic service and parking brake.
HYDRAULIC DECK LIFTING AND GRASS-CATCHER EMPTYING.
CUTTING HEIGHT: adjustable to 25-35-50-60-75-85-95-110 mm.
SEAT: super comfort, adjustable and sprung seat with arm-rests.
STEERING WHEEL: steering column, with height and tilt adjustment.
STEERING RADIUS: 620 mm.
HOURLY MOWING CAPACITY: 15,500 m
ACCESSORIES: 155 cm cutting deck with collection and anti-shock discs, weight 180 kg. 160 cm LMP cutting deck
with side and rear discharge and mulching, size with baffle 192 cm, weight 170 kg. Hydraulic kit for accessories.
Adjustable 165 cm snow blade with hydraulic control +/- 30°. 150 cm all-purpose flail with scarifying kit. Cabin, air
conditioning kit.
SIZE (with cutting deck): Length: 3420 mm, Width: 1620 mm, Height: 1830 mm (2160 mm with lifted roll-bar)
SIZE (without cutting deck): Length: 2500 mm, Width: 1350 mm.
CLEARANCE FROM THE GROUND: 180 mm.
DISTANCE BETWEEN AXLES: 1260 mm.
WEIGHT (without cutting deck): 1280 kg.
-
Make sure the machine is complete and that it has not suffered any damage during transit.
-
Check the levels of the engine oil (fig. 46) and hydrostatic transmission oil (fig. 4).
-
Check the tyre pressure:
Front wheels 24 x 12.00 - 12 (1.6 bar)
Rear wheels 20 x 10.00 - 10 (1.6 bar)
Deck wheels (1.5 bar)
-
Check the battery voltage, it must not be less than 12.5 Volts; recharge if necessary.
-
If a dry battery has been supplied with separate acid, to put the machine into service proceed as follows:
1) pour in the acid and wait 2 hours;
2) charge the battery with a charger set to 12 Volts on a slow charge for 2 hours.
Caution, if this procedure is not observed this could lead to the battery deteriorating and the acid leaking out
during work.
BATTERY
Caution! The gases released by the battery are explosive, so keep it away from naked flames or sparks. Check the
level of the liquid at regular intervals and keep the terminals greased with Vaseline.
FD2200 4WD/ Translation of the original instructions
grillo@grillospa.it
TECHNICAL SPECIFICATIONS
2
/h approx.
PUTTING THE MACHINE INTO SERVICE
7
Publicidad
